THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
Glen Convector Heaters
Models : EC532 and EC533
Installation and Operating Instructions
Dimensions
(millimetres)
Model
(
s
)
Specification
EC532
2.0kw Heat Switch
EC533
2.0kw Thermostat
Fig. 1
General
The heater may be used free standing on feet or wall mounted on
brackets. The necessary feet, screws and wall brackets are provided.
The heater should only be operated when in the upright position as
shown in Fig. 1 above.
To fit feet
Remove the two foot fixing screws from the transit position at each end
of the heater base (one screw holds the 3 wall brackets in place - see ‘a’
in Fig. 2). Retain the wall brackets for possible future use.
Locate the feet by aligning the pins in the feet with the holes in the
heater base. Secure each foot with the screws supplied (see ‘c’ in Fig.
2).
ON NO ACCOUNT SHOULD THE HEATER BE USED FREE STANDING
WITHOUT THE FEET FITTED.
Fig. 2
IMPORTANT SAFETY ADVICE
WARNING –THIS APPLIANCE MUST NOT BE USED IN A
BATHROOM
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING
POOL.
WARNING – THIS HEATER MUST NOT BE LOCATED
IMMEDIATELY BELOW A FIXED SOCKET OUTLET.
DO NOT USE THE HEATER UNTIL THE FEET OR WALL
BRACKETS ARE FITTED CORRECTLY.
FOLLOW these instructions carefully.
NEVER cover or obstruct in any way the heat outlet slots at
the top of the heater or the air inlet slots in the base of the
heater.
The heater carries a warning ‘DO NOT COVER’ to alert the
user to the risk of fire that exists if the heater is accidentally
covered.
If young children, the aged or infirm are likely to be left in the
vicinity of the heater, we advise that adequate precautions
should be taken.-
We recommend that a guard be fitted to ensure contact with
the heater is avoided and objects cannot be inserted into the
product.
If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
For further information, please contact our guard supplier
direct on Tel. No. 01603 667957, or in case of difficulty or for
further advice contact the Customer Helpline.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an ~ supply only and the voltage marked
on the heater must correspond to the supply voltage. This heater is
fitted with a rewirable plug incorporating a 13 amp fuse. In the event of
replacing the fuse in the plug supplied, a 13 amp fuse approved by
ASTA to BS 1362 must be used. If any other type of plug is used, a 15
amp fuse must be fitted in the plug, the adaptor, or at the distribution
board.
IMPORTANT : If the plug is not suitable for your socket, the 13 amp
plug should be removed. Before wiring the appropriate plug, please note
that the wires in this mains lead are coloured in accordance with the
following code :
GREEN AND YELLOW :
EARTH
BLUE :
NEUTRAL
BROWN :
LIVE
Connect the
GREEN AND YELLOW
wire to the terminal marked ‘
E
’ or
by the earth symbol
,
or coloured
GREEN
or
GREEN AND YELLOW
.
Connect the
BROWN
wire to the terminal marked ‘
L
’ or coloured
RED
.
Connect the
BLUE
wire to the terminal marked ‘
N
’ or coloured
BLACK
.
INGCUKEC53 Issue 1
425
MIN
545
230
MIN
Floor Mtd.
365
MIN
230
MIN
450
Wall Mtd.
shelf
230
Positioning the heater
Always ensure that the heater is stood on a firm, level base near to, but
not directly beneath, a suitable mains supply socket.
Ensure that curtains and furniture are not positioned close to the chosen
position, as this would create a potential fire hazard.
We recommend that the heater should be wall-mounted in rooms where
children may be left unattended.
See also ‘Important Safety Advice’
