Glensound DDA 1:6 User Manual Download

Page: 5 / 16

Page 5 of 16

This equipment manufactured by Glensound Electronics Ltd of Brooks Place

Maidstone Kent ME14 1HE is

marked and conforms to:

Low Voltage Directive: EN60065

Emissions: EN55103.1

Immunity: EN55103.2

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

REGULATIONS 2006 (WEEE)

Glensound Electronics Ltd is registered for business to business sales of WEEE in
the UK our registration number is:

WEE/JJ0074UR

RoHS2 DIRECTIVE

EC directive 2011/65/EU restricts the use of the hazardous substances listed below
in electrical and electronic equipment.

This product conforms to the above directive and for this purposes, the maximum
concentration values of the restricted substances by weight in homogenous
materials are:

Lead

0.1%

Mercury

0.1%

Hexavalent Chromium

0.1%

Polybrominated Biphenyls

0.1%

Polybrominated Diphenyl Ethers

0.1%

Cadmium

0.01%

Summary of Contents for DDA 1:6

















Search results

Summary of Contents for DDA 1:6

Reviews:

Related manuals for DDA 1:6

Brands by name

Popular brands

Glensound DDA 1:6, User Manual

Search results

Summary of Contents for DDA 1:6

Reviews:

Related manuals for DDA 1:6

Brands by name

Popular brands