background image

PREPARATION BEFORE RIDING

Always double check

 your bike before riding it (tighten the handlebars and stem, check the saddle, wheels, 

and brakes, etc.)

Check tyre pressure. 

Tyre pressure is indicated on the sidewall of the tyre.

Check your tyre pressure before each ride by squeezing the tyre between your thumb and fingers.

It should feel very firm, but not hard, when you sit on your bicycle, the tyre sidewalls should not 

compress very much under your body weight.

Use a hand or foot pump to inflate your tyres. 

NEVER 

inflate your tyres with an air compressor at a 

petrol station. 

Adjust the seat height and handlebar height

 

Please check the 

FOLDING&ASSEMBING INTRODUCTION

 

IMPORTANT TIPS & ADVICE

(I)

STRONGLY RECOMMEND THAT SIGNIFICANT MECHANICAL REPAIRS SHOULD BE 

CARRIED OUT BY A SKILLED BICYCLE MECHANIC.

(III)When you are riding on the road , make sure that you are always visible to other vehicles . 

Please respect the rules of the road in all circumstances

.

(IV)Speed must be slowed down in rainy and snowy days and in slippery areas. Braking distance 

should be increased to ensure safety.

Use the rear brake lever FIRST then the front brake lever

(V)

Cyclists must wear a reflective vest at night outside urban areas.

(VI)This product may be used by children 14 years of age or older. Those with reduced 

physical, sensory or mental capacity, or lack of experience or knowledge, should be properly 

supervised or given instructions for safe use of this bike.

(II)The tyre pressure range of this Ebike is 

250-300kpa(36.3-43.5psi) which marked on the tyre

Please ensure that the tyre pressure is within the range

 to avoid accidents.(1psi=6.895kPa)

Summary of Contents for EVOLT























Reviews: