background image

20

Visit our website at http://xtm.globalhobby.com or for Customer Service at http://globalservices.globalhobby.com

IMPORTANT WARRANTY SERVICE INFORMATION

Before returning your X-Terminator Pro for warranty consideration, the status of the unit must be within the guarantee as stated above.
Do not return your X-Terminator Pro to the place of purchase.  They are not authorized or equipped to perform warranty work on XTM
Racing products.  When requesting warranty service, please observe the following:

Crash damage will not be covered under warranty.  Do not request warranty service for a crash-damaged product.

This warranty only covers the XTM Racing X-Terminator Pro only.  It does not cover your own engine or radio control system.  Please

remove your engine, radio control system and batteries from the chassis before sending the product to us.

Include a note detailing the problem or service you are requesting.  Service cannot be provided without this information.  Include your

daytime phone number, shipping address and/or email address in the event we need more details pertaining to the service requested.

If your vehicle is out of the warranty period you may request an estimate of services at the time you return your vehicle for service.  An

omission of this request implies permission for Global Services to service your vehicle at our discretion.

Include a method of payment for any service charges.

Send the unit to us by United Parcel Service, Federal Express or by Insured Mail.  Postage is non-refundable.  Send your package to:

IMPORTANT WARRANTY INFORMATION - PLEASE READ!

Your XTM Racing X-Terminator Pro is warranted against manufacturer defects in materials and workmanship for a period of 90 days
from the date of purchase.  Warranty service will be provided within 90 days of the date of purchase only if you are able to provide the
original or a copy of the original dated sales receipt.

To locate the dealer nearest you, please call us at (714) 963-0133 or visit our dealer directory on the Internet at

www.globalhobby.com/where2buy.htm

or Order Directly From Us at the Address, Phone Number or Web Site Shown Above

Visit Our Website

http://globalservices.globalhobby.com

Global Services
18480 Bandilier Circle
Fountain Valley CA  92708

Phone: (714) 963-0329          Fax: (714) 964-6236           Email: service@globalhobby.net

PURCHASING REPLACEMENT PARTS

Included with your X-Terminator Pro is a separate booklet listing all of the replacement parts that are available, along with their
respective part numbers.  Replacement parts are available through your local authorized XTM Racing dealer or directly from us.

Summary of Contents for XTM Racing X-Terminator Pro





















Reviews: