background image

 

Global Water 

800-876-1172 

 globalw.com 

 

 

- 4 - 

 

IV.

 

Installing the 4-20mA Weather Station 

 

a.

 

Please refer to Appendix A prior to installing the 4-20mA Weather 
Station to review any optional sensor’s mounting instructions that may 
modify the standard setup. 

b.

 

Each sensor comes equipped with mounting hardware for a 1” 

diameter pipe. 

c.

 

The 4-20mA Weather Station stand consists of a 1” diameter stainless 
steel cross bar with a T fitting and the mast (two 1” diameter tubes 
connected together with a pvc insert).  The top piece of the mast has a 

T fitting with a 1” stub attached also. 

d.

 

Insert the bottom of the mast into a solid base and secure it.  Global 
Water sells a Tripod for this purpose, WE830. 

e.

 

Slide the top of the mast onto the pvc insert to complete the mast. 

f.

 

Mount the cross bar to the top of the mast using the attached T fitting.  
Tighten the set screw with the enclosed allen wrench.  Ensure that the 
cross bar is level.  NOTE: For best results the cross bar should be at 
least 8’ above the ground or roof. 

g.

 

The Wind Speed and Wind Direction sensors should be mounted on 
the opposite ends of the cross bar.  Loosen the set screw holding the 
Wind Direction sensor in the elbow. Line up the notches on the Wind 

Direction Sensor, turn the sensor until the notches face north, and 
secure the sensor.  

h.

 

The Temperature Sensor and Humidity Sensor are pressure fitted 
inside the Solar Shield.  The Solar Shield has a 1” elbow that mounts 

on the stub attached to the top portion of the mast.  Place the elbow 
on the stub and secure with the set screw. 

i.

 

If the mast is in an area of extreme wind it may be necessary to secure 
the 4-20mA Weather Station with guy wires (not included).  

 
 
 
 

 
 

Summary of Contents for WE900









Reviews: