background image

Instruction Manual

6

 

Outdoor Drinking Fountain w/ Bottle Filler

3. MOUNT PEDESTAL TO GROUND

M6 x 10 (qty 8)

•  

Locate and install plumbing through ground as required.

   Refer to Rough-In Guide (page 4) for proper location and

   correct plumbing.

•  

This unit is designed to be installed on the surface of an

   existing or new concrete slab, capable of supporting 400 lbs.

Position fountain base over plumbing and

secure to ground using provided anchor

kit (H3) mounting hardware.

2. INSTALL BUBBLER

2a.

 Unscrew and remove

nut and washers from

Bubbler (P1).

2b.

 Locate the hole on the drinking

fountain pan surface. Align and

sandwich with the two washers

and tighten the nut to secure

the bubbler.

2c.

 Bubbler is now

properly installed.

4. ATTACH BOTTLE FILLER TO PEDESTAL

Using a phillips-head screwdriver, assemble

the bottle filler to the pedestal using the

(8) M6 x 10 pan head screws (H4).

Anchor kit consists of:

- (4) M10 Nuts

- (4) M10 Lock Washers

- (4) M10 Standard Washers

- (4) M10 Anchors 

H4 

Pan Head Screw

Nut
Lock Washer
Standard Washer

Anchor

H3 

Anchor Kit

Summary of Contents for 761216












Reviews: