background image

USER MANUAL

BEAT-MV/BEAT-2

Edition: January 2016

      - 

INTRODUCTION

Revision: No. 1          

8

1.5

MEASURES OF PROTECTION AGAINST ACCIDENTS

1.5.1

Safety alert symbols:

This User Manual employs the following safety alert symbols:

Indicates  information,  considered  important,  but  not  hazard-
related.

When appears this hazard alert sign in this manual, carefully read
what is says. 

Indicates a hazardous situation that, if not avoided, will result in
death or serious injury.

Indicates a hazardous situation that, if not avoided, could result in
death or serious injury.

Indicates a hazardous situation that, if not avoided, could result in
minor or moderate injury.

1.5.2

Safety measures and dangers:

Please go by the following safety measures:

M

Keep the fusion control box out of the reach of non authorised personnel, non qualified
personnel and children. Protect the control unit from water, rain, snow, etc.

M

When  transporting  the  unit,  and  during  loading  and  unloading  operations,  the
appropriate precautionary measures must be taken to ensure that all unit components
are  completely  secured  in  the  vehicle,  and  that  they  are  free  from  impact  during
transportation.

M

Protect the electrofusion cables and the cable that goes to the power supply of cutting
objects.

M

All  damaged  cables  must  be  replaced  immediately  by  the  After-Sales  Service  of
STPAcuster.

M

Always plug the control box to a power supply provided with differential and ground
connection.

M

Do not expose the fusion control box to heavy weights. All slight damage caused to
the external frame or to other elements will have to be replaced immediately by the
After-Sales Service of STPAcuster.

Summary of Contents for BEAT-2

































Reviews: