background image

 

 11.  BU-353S4 SPECIFICATIONS 

 

Electrical Characteristics 

(Receiver)

 

 

 

GPS Chipset 

 

SiRF STAR IV GSD4e  

Frequency 

 

L1, 1575.42 MHZ 

C/A Code 

 

1.023 MHz chip rate 

Channels  

 

48 

Sensitivity  

-163dBm 

Accuracy 

 

 

Position Horizontal  

 

<2.5m 2D RMS SBAS Enable   

Velocity 

 

0.1m/sec 95% (SA off), 

Time 

 

1 micro-second synchronized to GPS time 

WAAS 

 

Enabled for North America product s (USGlobalSat, Inc) 

Datum 

 

 

Datum  

WGS-84 

Acquisition Rate 

 

 

Hot start 

 

8 sec., average (with ephemeris and almanac valid) 

Warm start 

 

35 sec., average (with almanac but not ephemeris) 

Cold start 

 

35 sec., average (neither almanac nor ephemeris) 

Reacquisition 

 

0.1 sec. average (interruption recovery time) 

Protocol 

 

 

GPS Protocol 

 

Default: NMEA 0183  (Secondary: SiRF binary) 

GPS Output Data 

 

SiRF binary >> position, velocity, altitude, status and control 
NMEA 0183 MEA0183 V3.0 protocol, and supports 
command: GGA, GSA, GSV, RMC, VTG, GLL v2.2 (VTG 
and GLL are optional) 

GPS transfer rate 

 

Software command setting (Default : 4800,n,8,1 for NMEA ) 

Dynamic Condition 

 

 

Acceleration Limit 

 

Less than 4g 

Altitude Limit 

 

18,000 meters (60,000 feet) max. 

Velocity Limit 

 

515 meters/sec. (1,000 knots) max. 

Jerk Limit 

 

20 m/sec**3 

Temperature 

 

 

Operating  

-40°~ 

80°C 

Storage  

-40°~ 

85°C 

Humidity 

 

Up to 95% non-condensing 

Power 

 

 

Voltage  

 

5V ±5% 

Current  

60mA 

typical 

Physical Characteristics 

 

 

Dimension 

 

2.32" x 1.65" x 0.82" (59mm x 47mm x 21mm) 

USB Cable Length 

 

60" (152 cm) 

Low Noise Amp 

 

 

Amplifier Gain w/out cable 

 

27 dB   Typical 

Filtering 

 

-25dB (+100 MHz) 

Output VSWR 

 

2.0 Max. 

Voltage 

 

DC 3 ~ 5.0V 

Current 

 

15mA  max @ 5VDC 

Due to continuous product improvements, all specifications are subject to change without notice.

 

 

 

 

Summary of Contents for BR-355S4
















Reviews: