background image

6

Design Description

The Clearly Solar, solar flat plate collector, collects the 

available solar radiation and transfers the heat through the 

solar fluid to be utilised by the system. 

It has been designed to compliment the complete range of 

Glow-worm solar system components. 

The kits are suitable for roof pitches between 15°- 75°, please 

choose from the table below. 

The solar thermal flat plate collector includes a saltwater-

resistant aluminium frame as well as a copper surface 

absorber with a high selective coating.

The flat plate collector has a CFC-free, standstill temperature-

resistant mineral wool insulation for long-life and excellent 

heat insulation.

Hydraulic connections are tool free with double ‘O’ ring 

sealing. The sensor sleeve is integrated into the hydraulic flow 

connection.

The following kits are available and dependant upon the 

number of collectors, the quantities required are listed in the 

following tables and illustrated in the appropriate sections:-

1 Technical Specification

On-roof installation components

1.1 On-roof mounting 

With on-roof mounting, flat collectors are fastened to 

horizontal mounting rails quickly and reliably with attachment 

clips. To ensure compatibility with different roofings, two 

different roof anchors are available: 

-  Type P for high profile (pantile)

-  Type S for flat profile (slate)  and extremely high protruding 

tiles (e.g. Mediterranean clay tiles).

High profile tiled roof (pantile)
Number of collectors

1

2

3

4

5

6

7

8

9

10

Type P anchor part no. 0020060302 - Section 5  

1

2

3

4

5

6

7

8

9

10

Easy fit hydraulic connection set 

part no. 0020060207

1

1

1

1

1

1

1

1

1

1

Easy fit hydraulic extension set 

part no. 0020055175

-

1

2

3

4

5

6

7

8

9

Collector panel

1

2

3

4

5

6

7

8

9

10

Low profile tiled roof (slate)
Number of collectors

1

2

3

4

5

6

7

8

9

10

Type S anchor part no. 0020055184 - Section 6  

1

2

3

4

5

6

7

8

9

10

Easy fit hydraulic connection set 

part no. 0020060207

1

1

1

1

1

1

1

1

1

1

Easy fit hydraulic extension set 

part no. 0020055175

-

1

2

3

4

5

6

7

8

9

Collector panel

1

2

3

4

5

6

7

8

9

10

Summary of Contents for Clearly Solar

















Reviews: