background image

GMC customer assist

If your product needs repairing, replacing, 
technical service or you simply need help or advice, 
please contact us on our Customer Assist Line 
1300 880 001 (Australia) or 0800 445 721 (New Zealand).

For prompt service we suggest you log your service request 
online at 

www.gmcservice.com.au.

 Should you not have 

access to the Internet, please contact our service department 
on 

1300 880 001 (Australia) or 0800 445 721 (New Zealand).   

7am –7pm, 7days a week (AEST).

Please note that if repair or replacement is required, 
you must provide a valid original purchase receipt.

You will need the following details at hand to log your service request; 

Personal details: 

First & Last name, address, pick up address, 

 

contact phone numbers, email address

Product details:

  Product number, date of purchase, retailer bought from, 

 

State & postcode, receipt number, reason for the request, 

 

copy of official purchase receipt

Attach your purchase receipt and save with this Manual for future reference.
Please refer to our website 

www.gmcompany.com

 for full GMC warranty Terms and Conditions.

Summary of Contents for LSM210A





















Reviews: