background image

7

 

Do not use the charging system if it has been subjected 

to a heavy knock, dropped or otherwise damaged in any 

way. Take the charging system to an authorised service 

centre for a check or repair.

 

Do not disassemble the charging system. Take it to 

an authorised service centre when service or repair is 

required. Incorrect re-assembly may result in the risk of 

fire, electric shock or electrocution.

 

To reduce the risk of an electric shock, unplug the 

adaptor charger from the power supply before attempting 

to clean it. Removing the battery alone does not reduce 

the risk.

 

Never attempt to connect two charging systems together.

 

Do not store or use the tool and battery pack in locations 

where the temperature may reach or exceed 40°C such 

as alongside sheds or metal structures in the summer.

 

The charger is designed for use from a standard 

household electrical supply (230 volts). Do not attempt  

to connect the adaptor charger to a supply with a  

different voltage.

Additional safety rules for the battery pack

 

The battery pack for this tool has been shipped in a low 

charge condition. You should charge the battery pack fully 

before use.

 

To ensure the longest battery life and best battery 

performance, always charge the battery when the air 

temperature is between 18–24°C. Do not charge the 

battery pack when the temperature is below 4°C, or above 

40°C. This is important. Failure to observe this safety rule 

could cause serious damage to the battery pack.

 

Do not incinerate the battery pack even if it is seriously 

damaged or can no longer hold a charge. The battery 

pack can explode in a fire.

 

A small leakage of liquid from the battery pack may occur 

under extreme usage or temperature conditions. This 

does not necessarily indicate a failure of the battery pack. 

However, if the outer seal is broken and this leakage 

comes into contact with your skin:

  - 

Wash the affected area quickly with soap and water.

  - 

 

Neutralise the liquid with a mild acid such as lemon 

juice or vinegar

  If the leakage gets in your eyes:

  -   

Flush your eyes with clean water for a minimum of 10 

minutes and seek immediate medical attention. Inform 

the medical staff that the liquid is a 25Ð35% solution of 

potassium hydroxide.

 

Never attempt to open the battery pack for any reason. 

If the plastic housing of the battery pack breaks open 

or cracks, immediately discontinue its use and do not 

recharge it.

 

Do not store or carry a spare battery pack in a pocket 

or toolbox or any other place where it may come into 

contact with metal objects. The battery pack may be  

short circuited causing damage to the battery pack, burns 

or a fire. If storing the battery pack, cover the terminals 

with a heavy insulation tape to ensure short circuit cannot 

occur. Batteries, when stored for a long period of time, 

will discharge.

 

Only charge the battery with the charger system supplied.

 

This battery pack contains nickel-cadmium batteries. 

Consult your local waste authority for information 

regarding available recycling and/or disposal options of a 

damaged or worn-out battery pack.

 

Do not leave a battery pack on charge for more than 8 

hours. It will damage the battery cells.

Discharging your battery

Discharge your battery pack by operating your screwgun, 

then remove the battery pack and cover the battery pack 

terminals with heavy duty adhesive tape to prevent a short 

circuit and energy discharge. Do not attempt to open or 

remove any of the components of the battery pack.

Summary of Contents for SG18V

















Reviews: