135
S
ICHERUNGEN
/FI-S
CHUTZSCHALTER
A
USGANGSLEITUNG
Schutzvorrichtungen der Ausgangsleitungen (empfohlene Werte)
Normale Sicherungen (gL-gG)
In (Nennstrom)/7
FI-Schutzschalter (
Auslösekurve
C)
In (Nennstrom)/7
D
IFFERENTIALSCHUTZ
Ist am Eingang kein Trenn-Transformator vorhanden und der vom Versorgungsnetz kommende Neutralleiter ist an den
Ausgangs-Neutralleiter der USV angeschlossen, so bleibt die Last des Neutralleiters der Anlage unverändert:
DER EINGANGS-NEUTRALLEITER IST AN DEN AUSGANGS-NEUTRALLEITER ANGESCHLOSSEN
DAS VERTEILERSYSTEM, DAS DIE USV VERSORGT, WIRD VON DER USV NICHT VERÄNDERT
ACHTUNG: Korrekten Anschluss an den Eingangs-Neutralleiter sicherstellen, andernfalls drohen
Geräteschäden an der USV.
Die Last des Neutralleiters wird nur bei einem vorhandenen Isoliertransformator bzw. bei USV-Betrieb mit
vorgeschaltetem, getrenntem Neutralleiter verändert.
Zum Betrieb mit gegebener Netzspannung kann ein am Eingang sitzender Differentialschalter einschreiten, da die Ausgangs-
und Eingangsleitung nicht voneinander isoliert sind. Es ist jedoch jederzeit möglich, an einem Ausgang mehrere
Differentialschalter anzubringen, die gemeinsam mit dem Differentialschalter am Eingang koordiniert werden.
Der vorgeschaltete Differentialschalter muss folgende Merkmale aufweisen:
Der Differentialstrom muss der Summe aus USV + Last entsprechen. Zur Vermeidung eines zu frühen Einschreitens
wird empfohlen, eine gewisse Toleranzspanne mit einzuberechnen (Empfehlung: 300mA)*
Typ B
Verzögerung mindestens 0,1s
* Der Leckstrom der Last wird mit dem der USV am Schutzleiter (Erdleiter) summiert
R.E.P.O.
Dieser isolierte Eingang wird verwendet, um die USV im Notfall über eine Fernsteuerung auszuschalten.
Werksseitig wird die USV mit überbrückten “Remote Emergency Power Off” (R.E.P.O.) Klemmen geliefert (siehe
“Vorderansichten der USV”). Um das Ausschalten im Notfall steuern zu können, muss die Brücke mit dem NC-Kontakt der
verwendeten Ausschaltvorrichtung ausgetauscht werden. Zum Anschluss ein zweifach isoliertes Kabel verwenden.
Im Notfall wird die USV durch Betätigung der Ausschaltvorrichtung auf Standby gestellt, da der R.E.P.O Befehl geöffnet wird
(alle Leistungsstadien sind aus) und keine Ladung mehr zugeführt wird.
Die R.E.P.O. Schaltung wird über Stromkreise Typ SELV eigenständig mit Strom versorgt. Eine externe Stromversorgung wird
daher nicht benötigt. Im geschlossenen Stromkreis (Normalzustand) beträgt die maximale Leistung 15mA.
Summary of Contents for GM 3100 PRO
