background image

spark plug wire is always disconnected and kept away from the spark plug to 

prevent unintentional engine starts.

CAUTION 

– Avoid contact with any hot surfaces or objects such as exhaust 

system, cylinder heads, or any other part of the drive system.

CAUTION

 – Store product where petrol and oil fumes cannot reach an open 

flame, spark or any other source of ignition.  Never store product for a long 

period of time without first draining fuel & oil and storing it appropriately out 

of direct sunlight, in an approved container.

CAUTION 

– The rollbar, brush bars and any other form of protective system 

will not protect the operator and passenger(s) from all external obstacles 

protruding into the operator/ passenger(s) compartment. 

CAUTION 

– Should the product start making unusual noises, excessive or 

loud noises, or abnormal vibrations, stop the product, remove spark plug 

connector and check the vehicle for damage. Any abnormal noises or 

vibrations are a warning that there are loose or faulty parts. Routine mainte-

nance or repair must be undertaken.

SAFETY INFORMATION

1. This product must not be modified from the original manufacturers original 

design and configuration.

2. This product shall not be used in competitive events such as racing, stunts 

etc. Such activities may result in loss of control.

3. Prior to each cycle of operation, the operator shall perform the checks 

outlined in this manual under the “pre-start checks” chapter. 

4. This product shall not be started unless operator and passenger(s) are 

inside the product and secured safely using the restraint system supplied. 

5. Long hair, loose clothes, jewellery must be removed, restrained or tied back 

before using this product, whether you are the operator or passenger.

6. This product shall only be refuelled by the operator or supervisor knowl-

CONSUMER RESPONSIBILITY

edgeable in refuelling techniques. 

7. The supervisor or operator shall personally recognise that all persons 

operating or riding this product are of sound mental and physical capacity, 

are of suitable age, height and weight, and are capable to operate this 

product comfortably, responsibly and safely. The operator / supervisor 

acknowledges that sections 1-6 have been completed and is liable from 

herein. 

 

a.

 The supervisor / operator shall only allow the use of this product  

 

after a demonstration of the product has been completed, and all  

 

operators and passengers are comfortable.

 

b.

 The supervisor / operator shall provide continuous supervision at all  

 times. 

 

c. 

The supervisor shall not allow anyone to operate or ride who has  

 

long hair, loose fitting clothing or jewellery that has not been secured  

 

or removed. 

8. The products operators and passengers shall adhere to the manufacturer’s 

instructions, recommendations and safety information. The products 

operators and passengers must adhere to all laws and road rules (local, state, 

national) at all times whether moving or stationary.

 

a.

 Operators and passengers shall stay seated and secure at all times  

 

whilst the product is in operation. 

 

b.

 Operators and passengers shall remain inside the product at all  

 

times, with arms, legs and any other products inside the product at all  

 

times whilst the product is in operation.

 

c.

 Operators and passengers shall use appropriate Australian Standard  

 

approved motorcycle helmets, boots, & suitable protective clothing. 

 

d. Shall observe minimum age restrictions.

 

e. 

Shall not ride with lose or unsecured clothing, long hair or jewellery  

 

that has not been removed or secured. 

 

f. 

Shall not smoke, use alcohol or illicit drugs whilst operating this  

 product.

 

g.

 Persons under the influence of alcohol or drugs (illicit or prescrip 

 

tion) shall not supervise, operate or be a passenger of this product.

 

h. 

Shall not operate on terrain not suitable for this product as outlined  

5.

Summary of Contents for HAMMER DUNE












































Reviews: