6
GD00Z-7 MOUNTING
7
GD00Z-7 CONNECTIONS
8
SYSTEM OPERATION
9
OPERATION NOTES
1. The warning light will flash and the warning beeper will sound for five seconds
before the door opener is activated.
STAY CLEAR OF THE DOOR AND DOOR
OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, the GD00Z-7
will allow user to try to operate the door one more time. If the second attempt fails,
the GD00Z-7 will go into lock-out mode. See Note #3.
3. If the GD00Z-7 is in lock-out mode and will not accept remote commands, activate
the door from the pushbutton wall console.
4. Once the GD00Z-7 has initiated the movement of the garage door, another
command cannot be sent for 30 seconds. This eliminates the chance of “bouncing”
the garage door and possibly damaging the garage door opener.
10
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE
CORRECTIVE ACTION
Unable to
include in
Z-Wave
network.
GD00Z-7 was not
properly excluded
from a previous
Z-Wave network.
1. Reset the GD00Z-7 by pressing the LINK button
5 times. A quick beep followed by a longer beep
will indicate the reset.
Reset should only be used in the case of a
missing or inoperative primary controller.
The GD00Z-7
flashes and
beeps when
activated but
the door does
not move.
Obstruction blocking
the door or incorrect
wiring.
2. Make sure that there are no obstacles
preventing the door from moving.
3. Make sure that the GD00Z-7 connection wires
are connected to the proper terminals on the
garage door opener. Trace the wires from the
garage door opener’s pushbutton wall console
to the door opener. This is where the GD00Z-7
connection wires should be connected.
The GD00Z-7
flashes and
beeps when
activated but
the door does
not move.
The tilt sensor signal
is not being received
by the GD00Z-7.
1. Pair the tilt sensor with the GD00Z Garage Door
Controller.
a. Press and hold the pair button on the side of
the GD00Z-7 main unit for about 7 seconds.
It will emit a short chirp.
b. Release the button.
c. Rotate the tilt sensor 90 degrees to trigger a
transmission. A short chirp should be heard.
d. If a short short chirp is not heard, rotate the tilt
sensor again.
2. Make sure the tilt sensor is mounted correctly
on the garage door, with the arrow pointing up.
3. Make sure the battery pull tab has been
removed from the tilt sensor.
4. Replace the battery in the tilt sensor.
NORTEK SECURITY & CONTROL LIMITED WARRANTY
This Nortek Security & Control product is warranted against defects in material and workmanship for twelve (12)
months.
This warranty extends only to wholesale customers who buy direct from Nortek Security & Control
or through Nortek Security & Control’s normal distribution channels. Nortek Security & Control does not warrant
this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s
warranty, if any.
There are no obligations or liabilities on the part of Nortek Security & Control LLC for
consequential damages arising out of or in connection with use or performance of this product or other
indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or
reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for
fitness, are valid only until the warranty expires.
This Nortek Security & Control LLC Warranty is in lieu of all
other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Nortek
Security & Control Returns at 1-855-546-3351 for an RPA# and other important details.
REGULATORY NOTICES
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate
the equipment.
Les changements ou modifications non approuvés expressément par la partie responsable de la conformité
pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-7 - P/N: 10016895 X3- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
The GD00Z-7 typically
mounts on the ceiling
near the opener and
the power outlet
Tilt sensor
mounted on
the top panel
of the door
THE GD00Z-7 CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE GD00Z-7 WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
3/16" HOLES
FOR ANCHORS
The optional adjustable
mounting bracket fits
3 ways on the GD00Z-7
The bracket snaps onto
indents on either side or
on the end of the GD00Z-7
Secure
bracket
with screw
Use the four screws
and anchors to mount
the GD00Z-7 above
the opener
INDENT
INDENT
Use the bolts and nuts supplied
to attach the bracket to a secure
structure
BE SURE THE GD00Z-7
IS CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
AND THE WARNING LAMP IS
NOT OBSTRUCTED
INDENT
1A
2A
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
! WARNING !
1
PU
SH
BU
TT
ON
PU
SH
BU
TT
ON
GARAGE
DOOR
OPENER
Connect the GD00Z-7 connection
wires to the pushbutton wall console
terminals on the garage door opener.
The terminals may be named "PWC", "WC",
"PB", "PUSHBUTTON", or "RED and WHITE".
Terminal names and locations vary by model.
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
Remove the screw from 120 VAC
outlet faceplate. Secure the power adapter
to the faceplate with the provided
screw. Plug into outlet.
USE WIRE TIES TO SECURE
EXCESS WIRING CLEAR
OF ALL MOVING PARTS
OF THE GARAGE
DOOR AND OPENER
Either wire can
connect to either
terminal
Plug the power cord
into the power input
jack on the GD00Z-7
2
1
3
FLASH
FLASH
FLASH
BEEP
BEEP
BEEP
Use your Z-Wave Controller to
activate your garage door opener
The GD00Z-7 will activate
the door opener and open
or close the door
STAY CLEAR
OF THE DOOR !!!
3
The GD00Z-7 will beep and
flash for five seconds before
the door moves
4
5
Restore power to your
garage door opener
1
To synchronize the system,
use the garage door opener's
pushbutton to manually open
and close the door
2
STAY CLEAR
OF THE DOOR !!!
Copyright © 2017 Nortek Security & Control LLC
10016895 X3
GD00Z-7 Specifications
Power Supply: Input: 120 VAC, 0.35 A
Output: 12 VDC, 1 A
Operating Temperature: -4°—122° F (-20°—50° C)
Audible Alarm: 45 db @ 10 feet
Strobe:
360 Lumens
Communications:
Z-Wave (908.4 MHz)
Mounting:
Screws and anchors to
the ceiling, or bracket to the
opener’s hanging hardware
Tilt Sensor Specifications
Power Supply: Type CR2032 Coin Cell Battery
Operating Temperature: -4°—122° F (-20°—50° C)
Battery Life: 24 Months (typical)
Communications:
Proprietary 345 MHz
Range:
100 feet line-of-sight to GD00Z-7
Mounting to Garage Door: Double-sided tape or two
mounting screws
(Specifications subject to change without notice)
NOTICE TO USERS IN CALIFORNIA - CR COIN
CELL LITHIUM BATTERY INFORMATION: THIS
PRODUCT CONTAINS A CR COIN CELL LITHIUM
BATTERY WHICH CONTAINS PERCHLORATE
MATERIAL - SPECIAL HANDLING MAY APPLY - SEE
www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY
IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO
NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL
OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND
RECYCLING REGULATIONS IN YOUR AREA.
