background image

 

WARRANTY 

 

WE WARRANT to the original purchaser the Gold Medal equipment sold by us to 
be free from defects in material or workmanship under normal use and service. Our 
obligation under this warranty shall be limited to the repair or replacement of any 
defective part for a period of six (6) months from the date of sale to the Original 
Purchaser with regard to labor and two (2) years with regard to parts and does not 
cover damage to the equipment caused by accident, alteration, improper use, voltage, 
abuse, or failure to follow instructions. 
 
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED 
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR 
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY. 
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION 
ON THE FACE HEREOF. We neither assume, nor authorize any other person 
to assume for us, any other obligation or liability in connection with the sale of said 
GOLD MEDAL equipment or any part thereof. 
 
The term “Original Purchaser” as used in this warranty shall be deemed to mean that 
person, firm, association, or corporation who was billed by the GOLD MEDAL 
PRODUCTS COMPANY, or their authorized distributor for the equipment. 
 
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL 
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800- 
543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE 
EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS 
CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. 
 
 

 

GOLD MEDAL PRODUCTS COMPANY 
10700 Medallion Drive 
Cincinnati, Ohio 45241-4807 USA 

www.gmpopcorn.com

 

Phone: 1-800-543-0862 
Fax: 1-800-542-1496

 

 
 
 
 

© The text, descriptions, graphics and other material in this publication are the proprietary 
and exclusive property of Gold Medal Products Company and shall not be used, copied, 
reproduced, reprinted or published in any fashion, including website display, without its 
express written consent. 

 

Summary of Contents for 5280


















Reviews: