background image

 

 

Pop-A-Lot

 

Model No. 2007, 2007BN, 2007ST, 2007EX, 2007STX 

 

Page 7 

 

 

gmpopcorn.com

Care and Cleaning 

 

 DANGER

 

Machine must be properly grounded to prevent electrical shock to personnel. 

DO NOT immerse in water. 

Always unplug the equipment before cleaning or servicing. 

025_020314 

 

 

 

WARNING

 

To avoid serious burns, DO NOT touch the kettle while it is hot! 

028_082715 

 
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only 
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of 
advertising your product. 

Note:

   It is extremely important to follow all of the cleaning procedures, otherwise 

parts damage and equipment failure will result. The warranty does not cover 
parts that are damaged due to improper cleaning. 

Daily Kettle Cleaning Instructions 

CAUTION:

 A hot kettle will cause burns if you touch it with your hand. Allow kettle to 

cool at least 1 hour before attempting to clean. 

DO NOT

 use ice or water to 

cool down a hot kettle! Severe kettle damage will result! 

1.

 

When cool, wipe the 

outside

 of the kettle with a clean, soft cloth. 

DO NOT

 use oven 

cleaners or abrasive materials as they will damage the kettle. 

2.

 

Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons 
per gallon of water. It is not necessary to use the entire gallon at once; only use 
enough to fill the kettle 1/2 inch deep.  

3.

 

Turn the kettle heat ON. When the water starts to boil, turn the kettle heat OFF.  

4.

 

Allow to cool for at least 1 hour, then dump the solution into a bucket and wipe the 
inside of the kettle with a clean cloth. Make sure all of the solution goes into the 
bucket; do not spill any in the interior of the machine. 

For an extra dirty kettle, the process may be repeated; or, after turning the kettle heat 
OFF, allow solution to sit in the kettle overnight. The next morning, dump the solution 
into a bucket and wipe the inside of the kettle with a clean cloth. 

5.

 

With the unit OFF and unplugged, wipe the kettle lead cord with a clean SLIGHTLY damp 
cloth. 

DO NOT get moisture into the kettle lead-in cord, severe damage will result.

 

 

 

Summary of Contents for Pop-A-Lot 2007
































Reviews: