background image

9

Terms & Conditions

Interpretation

1.  In terms and conditions:

(1)  “Goldacres” means Goldacres Trading Pty. Ltd. A.C.N. 061 306 732 trading as Goldacres 

Agricultural Equipment (its successors and assigns) which is the seller of the Goods;

(2)  “Purchaser” means the purchaser of the Goods;

(3)  “Goods” means the products and, if any, the services sold or provided by Goldacres to 

the Purchaser;

(4)  “GST Act” and “GST” are given the meanings referred to in a New Tax System (Goods 

and Services Tax) Act 1999.

(5)  “PPSA” means the Personal Property Securities Act 2009 (Clth) (as amended); 

(6)  Nothing in these terms and conditions shall be read or applied so as to exclude, restrict 

or modify or have the effect of excluding, restricting or modifying, any condition, 

warranty, guarantee, right or remedy implied by law (including the Competition and 

Consumer Act 2010) and which by law cannot be excluded, restricted or modified.

General

2.  (1) The Goods and all other products or services provided by Goldacres are provided 

subject to these terms and conditions. These terms and conditions and any terms and 

conditions incorporated herein by virtue of clause 3 hereto shall prevail over all other 

terms and conditions of the Purchaser or otherwise to the extent of any inconsistency.

(2)  These terms and conditions may not be modified or amended without the expressed 

written consent of Goldacres endorsed by the Managing Director of Goldacres Trading 

P/L.

Additional Terms and Conditions

3.  From time to time Goldacres may provide additional or extended warranties in respect 

of certain goods and/or services. Where such additional or extended warranties are 

provided to a Purchaser in writing they will be incorporated into these terms and 

conditions provided that in the event of any inconsistency between these terms and 

conditions and the terms of any additional or extended warranty, the provisions of the 

additional or extended warranty shall prevail.

Goldacres quotations.

4.  Unless previously withdrawn, Goldacres quotations are open for acceptance within the 

period stated therein or, when no period is stated, with 14 days only of the quotation 

date. Goldacres reserves the right to refuse any order based on any quotation within 7 

days of receipt of the order.

Packing

5.  The cost of any special packing and packing materials used in relation to the Goods 

shall be at the Purchaser’s expense notwithstanding that such cost may have been 

omitted from any quotation.

Shortage

6.  The Purchaser waives any claim for shortage of any Goods delivered if a claim in 

respect thereof has not been lodged with Goldacres within (7) seven days from the date 

of receipt of the Goods by the Purchaser.

Specifications, etc: Catalogues, etc: Quantities

7.  All specifications, (including but not limited to: drawings, particulars of weights, 

volumes, capacities, dimensions, load factors) are approximate only and any deviation 

shall not be taken to vitiate any contract with Goldacres or form any claim against 

Goldacres. The descriptions, illustrations, and performances contained in catalogues, 

price lists and other advertising matter do not form part of the contract of sale of 

the Goods. Where specifications, drawings or other particulars are supplied by the 

Purchaser, Goldacres’ price is made on estimates of quantities required. Should there 

be any adjustments in quantities above or below the quantities estimated by Goldacres 

and set out in a quotation, then any such increase or decrease shall be adjusted on a 

unit rate basis according to unit prices set out in the quotation.

Performance, Capacities, Chemicals, Liquids, Application Methods, Environmental Effects

8.  Any performance, volumes, and/or capacity figures given by Goldacres are estimates 

only. Goldacres shall be under no liability for damages for failure to obtain such figures 

unless specifically guaranteed in writing and any such written guarantee shall be subject 

to the recognised tolerances applicable to such figures. The suitability of chemicals and 

other liquids for any application and the application methods and the environmental 

effects shall be the sole decision and responsibility of the Purchaser and the user of 

the Goods. Goldacres gives no warranty as to the suitability of any chemicals or other 

liquids for any application, nor the application methods nor the environmental effects, 

which may result from the use of the Goods. Goldacres shall be under no liability for 

damages arising out of the use of any chemicals, liquids, or mixtures in the Goods nor 

for any application, nor for the application methods nor for the environmental effects, 

which may result from the use of the Goods.

Delivery/Service Times

9.  The delivery times and service times made known to the Purchaser are estimates only 

and Goldacres shall not be liable for late delivery, non-delivery or delay and under no 

circumstances shall Goldacres be liable for any loss, damage or delay occasioned by 

the Purchaser or its customers arising from the late or non-delivery or late installation of 

the Goods.

Loss or damage in transit

10.  Goldacres is not responsible for any loss or damage to Goods in transit. Goldacres shall 

render the Purchaser such assistance as may be necessary to press claims on carriers 

provided that the Purchaser shall have notified Goldacres and the carriers immediately 

the loss or damage is discovered on receipt of Goods and shall lodge a claim on the 

carrier within three days of the date of receipt of the Goods. Insurance of Goods in 

transit is the responsibility of the Purchaser.

Limit of Liability

11.  (1) Goldacres liability for Goods manufactured by it is limited to:

(a)  where the law implies consumer guarantees into these terms and conditions pursuant 

to Part 3.2 Division 1 of Schedule 2 to the Competition and Consumer Act 2010 

(C’th”) (“consumer guarantees”) which cannot be excluded and Goldacres breaches 

a consumer guarantee, the loss and damage the Purchaser is entitled to at law which 

cannot be excluded by these terms and conditions; 

and, in all other cases

(b)  making good any defects by repairing the same or at Goldacres option by replacement 

within a period not exceeding either 1000 hours or twelve calendar months, whichever 

comes first, after the Goods have been dispatched provided that:

(i)  the defects have arisen solely from faulty materials or workmanship;

(ii)  the Goods have not received maltreatment inattention or interference;

(iii)  accessories of any kind used by the Purchaser are manufactured or approved by 

Goldacres;

(iv)  where applicable, the seals on the Goods remain unbroken;

(v)  there has been no improper adjustment, calibration or operation;

(vi)  the use of accessories including consumables, hardware or software (not manufactured 

by Goldacres) has been approved in writing by Goldacres;

(vii)  no contamination or leakage has been caused or induced;

(viii)  any modification to the Goods have been authorised in writing by Goldacres;

(ix)  there has been no inadequate or incorrect use, storage, handling or application of the 

Goods;

(x)  there has been no use or operation of the Goods outside of the physical, electrical or 

environmental specifications of the Goods;

(xi)  there has been no inadequate or incorrect site preparations;

(xii)  there has been no inadequate or improper maintenance of the Goods;

(xiii)  it has not been caused by fair wear and tear; and

(xiv)  firstly the Goods have been thoroughly inspected and any damage (from whatever 

cause) to the Goods (and in particular – the structure, welding, seams, bolts, booms) has 

been repaired prior to the Goods being operated, used driven or moved and on each 

occasion the tanks are filled; and

(xv)  there has been no failure to comply with the requirements of all present or future laws or 

regulations relating to the Goods and/or the use and/or the operation of the Goods; and

(xvi)  there has been no failure to maintain a record of hours of operation (which record shall 

contain full details of all inspections, repairs and maintenance) and produce same to 

Goldacres at the time of the claim;

(xvii)  the defective Goods or any damaged part of the Goods are promptly returned free of 

cost to Goldacres or a representative of Goldacres;

(xviii) all warranty related repairs have been carried out with the prior authorisation of 

Goldacres;

(2)  If Goods or any part thereof are not manufactured by Goldacres, in particular engines, 

engine accessories, transmissions, transfer cases, differentials, tyres, tubes, batteries, 

radios and UHFs, the guarantee of the manufacturer thereof shall be accepted by the 

Purchaser and is the only guarantee given to the Purchaser in respect of the Goods 

or that part provided always that this clause does not seek to exclude the consumer 

guarantees;

(3)  In the case of hydraulic systems, Goldacres shall replace defective parts in accordance 

with clause 11(1) of these conditions, provided that the failure of the part was not related 

to contamination within the system, Goldacres shall not be liable for labour in the case 

of repairing hydraulic system defects;

(4)  Goldacres will not accept liability for damage attributed to fair wear and tear including 

but not limited to fair wear and tear to nozzles, chains, belts, filters, brake pads, 

polyethylene bushes and liquid pump valves, valve O-rings, diaphragms and seals;

(5)  Goldacres shall not be liable for and the Purchaser releases Goldacres from any claims 

in respect of faulty or defective design of any Goods supplied unless such a design 

has been wholly prepared by Goldacres and the responsibility for any claim has been 

specifically accepted by Goldacres in writing and in any event Goldacres liability 

hereunder shall be strictly limited to the replacement of defective parts in accordance 

with paragraph 11(1) of these conditions provided always that this clause does not seek 

to exclude the consumer guarantees;

(6)   Except as provided herein, all express and implied warranties, guarantees and 

conditions under statute or general law as to the merchantability, description, quality, 

suitability or fitness of the Goods for any purpose or as to design, assembly, installation, 

materials or workmanship or otherwise are hereby expressly excluded and Goldacres 

shall not be liable for physical or financial injury, loss or damage or for consequential 

loss or damage of any kind arising out of the supply, layout, assembly, installation or 

operation of the Goods or arising out of Goldacres negligence or in any other way 

whatsoever;

(7)  The benefit of any warranty provided under these terms and conditions shall only be 

available to the Purchaser and shall not be transferable by the Purchaser;

(8)  The warranties provided under these terms and conditions do not extend to second 

hand or used Goods that may be sold by Goldacres.

12.  Goldacres liability for breach of a consumer guarantee is hereby limited (in the case of 

goods and services not used for personal, domestic or household purposes) to:

(1)  in the case of Goods, any one or more of the following:

(a)  the replacement of the Goods or the supply of equivalent Goods;

(b)  the repair of the Goods;

(c)  the payment of the cost of replacing the Goods or acquiring the equivalent Goods;

(d)  the payment of having the Goods repaired; or

(2)  in the case of services;

(a)  the supplying of the services again; or

(b)  the payment of the cost of having the services supplied again.

Prices

13.  (1) Unless otherwise stated in writing by Goldacres, all prices quoted by Goldacres are 

inclusive of GST for supplies within Australia and exclusive of GST for exports outside 

of Australia. Prices quoted are those ruling at the time of quotation or the date the price 

is given and are based on rates of freight, insurance, customs, duties, taxes, exchange, 

shipping expenses, sorting and stacking charges, cartage, cost of materials and 

other charges affecting the cost of production ruling on that date and any alterations 

thereto either before acceptance of or during currency of the contract shall be to the 

Purchaser’s account.

(2)  For the purpose of 38-185 of the GST Act, the day upon which the seller gives the 

Summary of Contents for 3PL 1000L





























































Reviews: