background image

29

Suction Filter

It is essential to maintain all filters, and filter 

screens, in good condition. Filter screens that 

are not regularly cleaned can severely impede 

the flow and thus affect delivery pressure. 

If the screen is in any way damaged, it can 

allow foreign material into the pumping 

system which can result in damage to the 

pump, lines, valves and nozzle tips. If the 

screen is not properly fitted, it can allow air 

into the pumping lines which will reduce the 

performance of the pump. The filter screen 

should be cleaned after every spraying 

operation. The best way to clean the filter 

screen is with a soft brush or compressed air 

after washing the entire chemical residue from 

the pump. 

SAFETY SHUT-OFF VALVE

The safety shut off valve enables the filter bowl 

to be removed while automatically shutting off 

the supply line to the filter. As the filter bowl 

is removed together with the bowl cap, the 

valve plunger seats so as to seal off the filter 

from the supply line. Replacing the filter bowl 

unseats the valve plunger and thus opens the 

supply line to the filter. 

SUCTION FILTER CLEANING

WARNING:

 Appropriate PPE must be worn 

when cleaning filters. 

1. 

Ensure the pump is turned off.

2. 

Carefully unscrew filter nut and remove 

bowl and avoid contact with residual 

chemical.

3.  Remove screen and clean (with a soft 

brush or compressed air).

4.  Check for damage to screen, bowl,body 

and O-ring.

5.  Place screen back in position.
6.  Make sure O-ring is in position for proper 

seal.

7.  Replace bowl and screw nut on. Do not 

over-tighten nut. 

Filling

When filling the sprayer it is necessary to use 

an external water source.

WARNING

: Operators must wear the 

appropriate PPE.
The following steps should be followed when 

filling the tank:

1.  With sprayer mounted on the vehicle, park 

on level ground.

2. 

The pump should be turned off.

3.  Remove the tank lid.
4.  Add 20% of the tanks volume of clean 

water, or more, if the chemical is in a 

denser form e.g. powder.

5.  Add chemical as required. Some agitation 

will take place as the rest of the water is 

added.

6. 

Use external water source to fill main tank 

(Do not exceed the tank capacity).

7.  Replace the tank lid and ensure that it is 

secure prior to switching on pump. You are 

now ready to use the sprayer.

WARNING

: When filling tank with water, 1 

litre of water will add 1 kg of weight. Some 

chemicals have a higher density than water 

and will weigh more per litre. Therefore, it 

is the operators responsibility to ensure the 

loaded weight of the sprayer does not exceed 

the towing and / or carrying capacity of the 

vehicle.

Summary of Contents for GA4908090

















































































Reviews: