background image

27

Lubrication

To ensure maximum life and performance 

from the sprayer, grease points should be 

periodically re-lubricated according to the 

maintenance schedule. These include the axle 

hubs, leaf spring pivots and boom hinges.

A quality 

multi purpose grease

 should be 

used when lubricating your equipment.
An 

SAE 15W40 engine oil

 should be used in 

the diaphragm pump.

Maintenance

To ensure maximum life and performance from 

the sprayer, follow the maintenance schedule 

set out below:

Corrosion Prevention

To ensure maximum life and performance from 

the sprayer, G15 anti-corrosion spray has been 

applied at the time of manufacture. It is used 

on all fasteners such as bolts, nuts, washers 

and any zinc plated components.
G15 anti-corrosion spray should also be 

applied to the sprayer pre and post season.

The amount of corrosion protection necessary 

will ultimately depend on local and operating 

conditions.

Frequency

Maintenance Tasks

8 Hour

Check pump oil level & condition

8 Hour

Check tyre pressure

8 Hour

Check wheel nuts are torqued correctly to 100 Nm (74 ft/lb)

8 Hour

Clean suction filter if blocked

25 Hour

Grease wheel bearings

25 Hour

Grease leaf spring pivots

50 Hour

Check Aluminium outer boom bolts

50 Hour

Grease boom hinges

150 Hour

Check wheel bearings for sideways movement

300-350 Hour

Change pump oil

3 Months

Check bolts on axle bearing caps

Yearly

Clean wheel bearings, inspect, re-grease and set rolling torque

Yearly

Carry out a complete decontamination of the sprayer

Summary of Contents for Prairie Compact 400L













































Reviews: