Golden Dragon XML6125CLE Repair Manual Download

Page: 235 / 613

10.6

Assembling and installing the control arms

10.6.1

Assembling the control arms (variant with retaining ring)

Special tools:
•

AA00.249.031 alignment part

•

5870.506.134 Press-in bush

•

AA02.293.799 Compression sleeve

Always install completely new repair kits.

Assembling control arms with joints

Slide joint into control arm.

On variant with spacer ring, place spacer ring

centrally on joint.

With AA00.249.031 [alignment part], align

joint flush.

Fig. 164

Install retaining ring as far as possible in bore

so that opening 45° to shaft of control arm is

twisted.

On variant with open spacer ring, align

opening of retaining ring opposite

opening to spacer ring.

Preload joint with hydraulic press,

5870.506.134 [Press-in bush], and

AA02.293.799 [Compression sleeve] until

retaining ring can be installed completely.

Insert retaining ring.

Release press.

Check that retaining ring is correctly seated.

Fig. 165

Assembly

EN 4474.751.104a - 2018-06

4-98

Summary of Contents for XML6125CLE

































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XML6125CLE

Reviews:

Related manuals for XML6125CLE

Brands by name

Popular brands

Golden Dragon XML6125CLE, Repair Manual

Search results

Summary of Contents for XML6125CLE

Reviews:

Related manuals for XML6125CLE

Brands by name

Popular brands