background image

Page 16

 

 

Changing the jets:

 

1.

 

Remove pan supports, burner heads and cups.

 

2.

 

Use a 7mm socket to unscrew and remove the jets, replacing them 

with those supplied in the kit. Ensure that the correct jets are fitted 

to the corresponding burner ( see spec table)

 

3.

 

Fit the gas type label supplied with this kit next to the gas connec-

tion point and remove existing label.

 

 

Setting the minimum flame level:

 

1.  Remove panels, knobs and water dish.

 

2.  Reasemble the burner heads, caps and knobs.

 

3.  Light one of the burners and turn the tap to maximum flame.

 

4.  Use a thin blade screwdriver to turn the by

-

pass screw located on 

the right of the gas tap shaft as show in the image on the right.

 

       Turn the by

-

pass screw fully counter clockwise. The result 

should be a small, stable flame which is uniform around the entire 

burner ring, if not turn the by

-

pass screw clockwise until satisfied 

with the flame. 

 

5.  Check that the burner does not go out when the tap is turned 

quickly from the maximum to minimum position.

 

6.  Repeat for each burner.

 

7.  Remove the burner heads caps and knobs

 

8.  Reassemble panels, burner heads, caps, knobs and pan supports.

 

Gas Conversion (NG to LPG)

 

If the required gas conversion kit is not supplied with 

your appliance, Gas conversion shall only be undertaken 

by an authorized person.

 

The NG to LPG conversion kits contains:

 

• 

Test point adaptor

 

• 

Auxiliary jet dia 0.50mm

 

• 

LPG gas type label

 

• 

Semi rapid jet dia 0.65

 

• 

Wok jet dia 0.5mm (Inner) + dia 1.10mm (Outer)

 

GAS CONVERSION ( LPG TO NG)

 

If the required gas conversion kit is not supplied with your appliance, you can 

order one from GOLDLINE.

 

Gas conversion shall only be carried out by by an authorized service techni-

cian.

 

The conversion kit contains:

 

-

NG regulator

 

-

NG Gas type label

 

-

Auxiliary jet dia 0.9mm

 

-

semi Rapid jet dia 1.1mm

 

-

Wok jet dia 0.8mm ineer and 1.8mm outer

 

Summary of Contents for SAB Series





















Reviews: