background image

1.

Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual. 

2.

It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.

3.

The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.

4.

Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.

5.   Make sure all parts are properly tightened

each time you use the weight bench. Replace
any worn parts immediately. 

6.   Keep children under 12 and pets away from

the weight bench at all times.

7.  Keep hands and feet away from moving parts.

8.

Always wear athletic shoes for foot protec-
tion while exercising.

9.

Always set both weight rests and both
weight spotters at the same height. 

10. Make sure that the cable remains on the pul-

leys at all times. If the cable binds as you are
exercising, stop immediately and make sure
that the cable is on the pulleys.

11. The weight bench is designed to support a

maximum user weight of 250 pounds, and a
maximum total weight of 560 pounds. Do not
place more than 310 pounds, including the
barbell, on the weight rests. Do not place
more than 200 pounds on the weight carriage
or more than 150 pounds on the leg lever.
Note: The weight bench is designed to be
used with an Olympic barbell. The weight
bench does not include a barbell or weights. 

12. Always place an equal amount of weight on

each side of the weight carriage or barbell.

13.

Always exercise with a partner. Your partner
should be ready to catch the barbell if you
cannot complete a repetition.

14. Always move the bench out of the way when

performing squat exercises. Always discon-
nect the lat bar from the cable when perform-
ing an exercise that does not require it. 

15. If you feel pain or dizziness at any time while

exercising, stop immediately and cool down.

WARNING:

Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product. 

WARNING: 

To reduce the risk of serious injury, read the following important precautions

before using the weight bench.

IMPORTANT PRECAUTIONS

3

Summary of Contents for GGBE35422

























Reviews: