background image

5

M8 Split Washer 

(72)––4

M6 Locknut 

(56)––4

M8 Locknut 

(66)––4

M10 Split

Washer (54)––3

M6 x 38mm Button 

Bolt (57)––4

M10 x 17mm Patch 

Screw (55)––3

M4 x 4.5mm 

Patch Screw 

(70)––1

M4 x 16mm 

Screw (77)––4

M8 x 16mm Patch 

Screw (84)––2

M8 Washer 

(85)––2

Wave Washer 

(78)––2

M10 x 78mm Patch Screw (65)––2

M10 x 22mm Patch 

Screw (4)––5

Assembly requires two persons. 

Place all parts of the exercise bike in a cleared area and remove the packing 

materials. Do not dispose of the packing materials until assembly is completed.

In addition to the included tool(s), assembly requires an adjustable wrench                     and a Phillips 
screwdriver                    .

Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each 
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the 
key number is the quantity needed for assembly. 

Note: If a part is not in the hardware kit, check to see if it 

has been preassembled. To avoid damaging parts, do not use power tools for assembly.

ASSEMBLY

Summary of Contents for WHIRLWIND 390





















Reviews: