INTRODUCTION
SYSTEM CHARACTERISTICS
33
O
O
O
O
O
O
O
O
O
O
O
O
O
Digital relay for
and
systems, which permits the following operation modes:
Relay for additional call repeater.
Relay for 2nd door Lock release.
Bus relay.
Need to configure or program depending on the mode of operation.
Can be installed at any point of installation (see operation modes).
It connects directly to the bus as another element of the installation.
Easily configurable through easy access microswitch.
Programming status led.
Jumper JP1 selects whether the relay is connected to a
or
system.
Potentiometer PT1 sets the relay operating time.
The maximum current for relay contact will be of 1.8A at 30 Vdc/250 Vac.
The minimum wire section to connect in the relay outputs will be 1.5 mm .
The product includes a fuse of 250V 2A F. Compliance with EN60127-1/EN60127-2 Standards.
The product includes a 120 ohm resistor for End of line (only V2Plus system).
Use Golmar wire
for bus connection to
system.
2PLUS
V2PLUS
2PLUS
V2PLUS
RAP-2150
V2PLUS
Ü
Ü
Ü
2
First of all we would like to thank and congratulate you for the purchase of this product manufactured by
Golmar.
The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification
and for the manufacturing of products like this one.
Its advanced technology and exacting quality control will do that customers and users enjoy with the
legion of features this system offers. To obtain the maximum profit of these features and a properly wired
installation, we kindly recommend you to expend a few minutes of your time to read this manual.
INDEX
Introduction ...........................................33
Index.....................................................33
System characteristics..............................33
Safety precautions...................................34
Operation modes .......................................
Relay for additional call repeater.............35
Relay for Lock release ............................35
Bus relay .............................................36
Description ............................................37
Installation.................................................
Detail of relay unit installation.................37
Configuration of relay unit .....................38
System selection jumper ........................38
Adjustment potentiometer......................39
Programming Led .................................39
End of line (only V2Plus system)...............39
Programming .............................................
Additional call repeater .........................40
Configuration (2Plus system) ........................
Additional call repeater .........................41
Bus relay .............................................41
Relay for Lock release ............................42
Configuration (V2Plus system) ......................
Additional call repeater .........................43
Bus relay .............................................43
Relay for Lock release ............................44
Installation diagrams...................................
Relay unit (2Plus system) ........................45
Relay unit (V2Plus system) ......................46
Troubleshooting hints ..............................47
Notes...............................................48-50
Compliance...........................................51
F U S E
34
SAFETY PRECAUTIONS
To access the output terminals of the relay, remove the
protection cover using flat pliers, by a light pressure
on the ribs wall and then pull to remove it.
Important:
To avoid an electrical shock, the installation and handling of the relay unit must be performed
by
and in the absence of electrical current.
authorized personnel
Remember:
When the installation and wiring works are finished,
make sure the protection cover and fuseholder are
placed in the relay unit before replacing the electrical
current.
F U S E
Warning:
O
O
O
O
O
O
O
Install the relay unit in a dry and protected place without risk of drip or water projections.
To avoid damage, the relay unit has to be firmly fixed.
The minimum wire section to connect in the relay outputs will be of
.
To avoid an electrical shock, neither remove the protection cover nor handle the connected
wire in the terminals with the symbol
, the installation and handling of the relay unit must
be performed by
and in the absence of electrical current.
In case of blown fuse, replace for one of the same characteristics (see page 33).
The blown fuse must be replaced by
and in the absence of electrical
current.
The maximum current for relay contacts will be of 1.8A at 30 Vdc/250 Vac.
For safety the cover of the fuseholder must always be placed.
1,5mm
authorized personnel
authorized personnel
2
Summary of Contents for SAR-2Plus
Page 1: ...FUSE TSAR 2PLUS ML rev 0110 SAR 2PLUS Digital relay unit instructions manual ...
Page 17: ...48 NOTAS NOTES ...
Page 18: ...NOTAS NOTES 49 ...
Page 19: ...50 NOTAS NOTES ...
