5
CARE AND MAINTENANCE
TROUBLESHOOTING
WARRANTY
EMC Compliance:
Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do
not spray cleaner directly onto any part of the fixture or LEDs.
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Light does not come on.
1. Power/ light switch is off.
2. Fixture not properly wired to junction box.
3. It is daylight.
1. Verify power supply and light switch is on.
2. Check wiring connections.
3. Recheck at night.
Light does not come on at night
1. Light may be installed in lighted area.
2. Wall switch and/or circuit breaker is off.
3. Incorrect or loose wire connections.
1. Light is operating as it was designed.
2. Turn on wall switch and/or circuit breaker.
3. Access outlet box and fix wire connections.
Light turns on during daylight
hours.
1. Light may be installed in shadows/dark area.
1. Shine a flashlight onto the light sensor. If the outdoor
light turns off then the fixture is mounted in an area
that does not allow enough light to enter the sensor.
Light is operating as it was designed. Relocate
fixture.
Fuse blows or circuit breaker trips
when light is turned on.
1. Discontinue use.
1. Call customer service
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (5) years from the date of original
purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential
environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has
been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original
purchase receipt showing date of purchase. Call
1-800-291-8838
to obtain a return authorization number and an address where to ship your defective
product. Note: C.O.D. shipments will
NOT
be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture
product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability
of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature;
(III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of
the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
For bulb warranty, please see box.
This device complies with CAN ICES-005 (B) / NMB-005 (B) rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to CAN ICES-005 (B) / NMB-005 (B) rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different
from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
Responsible party name: Good Earth Lighting, Inc.
Address: 1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA
Telephone number: 1-800-291-8838
REPLACEMENT PARTS LIST
REPLACE BULB
REPLACE GLASS
Replacement Diffuser Model #
ZD-CO1290L01-BK2 - sides
ZD-CO1290L02-BK2 - corners
Hardware Kit #
ZH-CO1297F01-BK2
Replacement Bulb #
ZB-LA8W-2700FIL
Replacement dusk to dawn
sensor
ZP-1290-SENSOR
Printed in China
Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
Shut off power at the
circuit breaker or fuse
panel before removing the
bulb.
Remove the old bulb by
twisting counterclockwise
until bulb is fully removed
from the socket. Repeat
step 9 to re-install bulb.
MAX 120V, 60Hz 100W TYPE
A INCANDESCENT BULB 23W
SELF-BALLASTED LED or CFL
BULB
1. Remove cage from the canopy by unscrewing the two screws at the top.
2. Remove silver screws holding the glass.
3. Remove the Silicone pads.
4. Carefully remove the broken glass.
5. Use existing silicone pads and transfer to new glass panel.
6. Insert Glass replacement and screw it back in place.
7. Reinstall cage to canopy.
Silver
screws
Silicone
pad
