CONTROL PANEL
FACING DOWN
45°
MAX.
SENSOR ORIENTATION
LIGHT ORIENTATION
Aim the PIR sensor toward the
intended detection area.
The PIR control panel should
face downward for easy access
Adjust the light according to the
mounting location with the imprint
always pointing up.
In one hand hold the fixture up, and with the other, connect the disconnect plug side hooked up to the junction box into the disconnect plug side
connected to the fixture. Carefully, push excess wires and the electric disconnect-plug back into electrical box.
Align the center holes of the fixture and mounting strap (attached to the J-box). Insert the long machine screw
(CC)
through the fixture’s center hole and
drive into the strap. Restore power to the electrical box and turn light on.
Note:
Keep the ladder out and proceed to follow the app instruction for
download and pairing. The pairing button is located on the bottom of the passive infrared sensor (PIR).
CC
x1
3
4
3
4
GND
FRON
T
Note:
Make sure the supply wires are connected
securely and captured by the internal contacts of the
plug. Gently pull on each wire to insure it remains
connected
Note:
Ground wires are normally a
green or bare copper wire.
Note:
The electrical disconnect plug is a
2 part connector.
PIR DETECTION
Good Earth Lighting
®
- 8 YEAR LIMITED WARRANTY:
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (8) years from the date of original
purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environ-
ment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been
discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original
purchase receipt showing date of purchase. Call
1-800-291-8838
to obtain a return authorization number and an address where to ship your defective
product.
Note:
C.O.D. shipments will
NOT
be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture
product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability
of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature;
(III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the
product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
FCC STATEMENT:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1)
Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the
dealer or an experienced radio/TV technician for help.
REPLACEMENT PARTS LIST:
Hardware Kit: ZH-SE1303F02
FCC responsible party name :
Good Earth Lighting, Inc.
Address:
1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA
Telephone number:
1-800-291-8838
7 ft
50 ft
PIR points down 5°
The figure below shows the PIR detection coverage:
Distance
2
