GoodHome bamia 3663602434313, Manual

18

EN Use

FR Utilisation

PL Użytkowanie

RO Utilizare

Setting the Movement Sensor
Within 30 seconds of turning on the mains power, press the Timer and Light Icons together 

 for 2 seconds to adjust the 

Movement Sensor. Repeat this process to alter the sensor setting if required. The LED display will show the selected mode.
Sensor enabled 

 the display will flash for 5 seconds - default setting.

Sensor disabled 

 the display will remain solid for 5 seconds.

Note: To change any of these settings at a later time, you must switch off the power at the mains outlet first. Wait a 

few seconds, turn on the power again and adjust as required.

02

General Use

On/Off 
1.  Touch the Hood On/Off Icon   and the glass panel of the cooker hood will open. The fan will turn on at speed 1 and 

the light will come on at the last setting used. All icons will be white apart from the Light Icon   which will be blue if 
the light was already on.

2.  Press the On/Off Icon again to turn off the cooker hood; the glass panel will close and the fan will switch off. The 

light will also turn off automatically after 5 minutes. If you wish to leave the light on for an extended time, manually 
switch on at the control panel.

Movement Sensor 

 (if enabled)

You can switch on the cooker hood by passing your hand in front of the Movement Sensor. Note you cannot turn off the 
cooker hood using the Movement Sensor, you must touch the Hood On/Off   Icon instead.

Light On/Off 
1.  Touch the Light Icon to turn on the downlight and also the ambient light (if enabled).
2.  To change the brightness of the downlight, touch and hold the Light Icon   until the display shows the brightness 

sequence. Remove your finger from the Light Icon   when the desired brightness is achieved. The sequence runs from 
L1 to L5 and back to L1 in steps. The selected brightness will flash for a few seconds and revert to the fan speed display.

Fan On/Off and Speed Reduction 
1.  If the fan motor is set at speeds 2, 3, 4, 5 or P, pressing the Fan Decrease Icon   will reduce the speed by one level at a 

time. If you press the Fan Decrease Icon    for more than two seconds, the speed will drop to speed 1 from any other level.

2.  If the fan motor is set at speed 1, pressing the Fan Decrease Icon   will result in the motor switching off. However 

the downlight will remain on (if enabled) and the display will show the current brightness level.

Boost Function and Speed Increase 
If the fan motor is set at speeds 1, 2, 3, 4 or 5, pressing the Fan Increase Icon   will increase the speed by one level at 
a time. If you press the Fan Increase Icon   for more than two seconds, the speed will increase to full power from any 
level and the display will flash.

NOTE: Full power or Boost (P) only operates for five minutes maximum to conserve energy and the fan speed will 

automatically drop to speed level 5 after this time.

Setting the Timer 
1.  When the fan motor is on and the Timer Icon   is pressed the icon will flash blue and the display will show the 

current fan speed.

2.  The chosen speed level will remain in use for five minutes before dropping down to the next lowest speed. This speed 

will remain in operation for two minutes before dropping down again. This will be repeated every two minutes unless 
the speed is already at level 1 and then the fan will turn off. If the light is already on, this will also be turned off.

3.  Pressing the Fan Decrease Icon   or Fan Increase Icon   during a current timer program will restart the countdown 

process again with the first five minute cycle.

4.  If the Timer Icon   is pressed again during a current timer program, the cycle will be cancelled. The Timer Icon   

will revert to white and the current fan speed will remain on indefinitely.

5.  The maximum timer program cycle is 15 minutes: 5 minutes on P and then 2 minutes each on speed 5 down to speed 1.