background image

5151 San Felipe Suite 500 • Houston, TX 77056

www.goodmanmfg.com • www.amana-hac.com

©

 2009-2011 Goodman Manufacturing Company, L.P.

 

C

US

®

ATTENTION INSTALLING PERSONNEL

RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.

Installer:  Affix all manuals adjacent to the unit.

These furnaces comply with requirements em-
bodied in the American National Standard / Na-
tional Standard of Canada ANSI Z21.47·CSA-
2.3 Gas Fired Central Furnaces.

As a professional installer, you have an obligation to know the product better than the customer.

This includes all safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual.

Pay special attention to all safety warnings. Often during installation or repair, it is possible to place yourself

in a position which is more hazardous than when the unit is in operation.

Remember, it is 

your

 responsibility to install the product safely and to know it well enough

to be able to instruct a customer in its safe use.

Safety is a matter of common sense...a matter of thinking before acting.

Most dealers have a list of specific, good safety practices...follow them.

The precautions listed in this Installation Manual are intended as supplemental to existing practices.

However, if there is a direct conflict between existing practices and the content of this manual,

 the precautions listed here take precedence.

NOTE

: Please contact your distributor or our website for the applicable Specification Sheet

referred to in this manual.

G

OODMAN

 

WILL

 

NOT

 

BE

 

RESPONSIBLE

 

FOR

 

ANY

 

INJURY

 

OR

 

PROPERTY

 

DAMAGE

 

ARISING

 

FROM

 

IMPROPER

 

SERVICE

 

OR

 

SERVICE

 

PROCEDURES

.

 

I

F

 

YOU

 

INSTALL

 

OR

 

PERFORM

 

SERVICE

 

ON

 

THIS

 

UNIT

,

 

YOU

 

ASSUME

 

RESPONSIBILITY

 

FOR

 

ANY

 

PERSONAL

 

INJURY

 

OR

 

PROPERTY

 

DAMAGE

 

WHICH

 

MAY

 

RESULT

.

 

M

ANY

 

JURISDICTIONS

 

REQUIRE

 

A

 

LICENSE

 

TO

 

INSTALL

 

OR

 

SERVICE

 

HEATING

 

AND

 

AIR

 

CONDITIONING

 

EQUIPMENT

.

WARNING

IO-359J
1/11

I

NSTALLATION

 I

NSTRUCTIONS

 

FOR

 *M(H,S)8 / *D(H,S)8 / *HS8 / GME8 G

AS

 F

URNACE

(CATEGORY I )

Summary of Contents for *MH80453A Series

















































Reviews: