background image

TABLE OF CONTENTS

Introduction ...................................................................................................

1

Crane Operator Instructions .........................................................................

2

Safe Operating Guidelines ...........................................................................

3

Installation

     Step 1  - Pre-assembly ............................................................................................4-5

     Step 2  - PIVOT PRO® (Wall/Column Mounted) Boom Installation ........................6-7

     Step 3  - PIVOT PRO® (Free Standing) Mast Installation ......................................8-9

     Step 4  - PIVOT PRO® (Free Standing) Boom Installation .................................10-11

     Step 5  - Vacuum Hose Installation ..........................................................................12

     Step 6  - Accessories (Optional) Installation .......................................................13-15

     Step 7  - Final Steps .................................................................................................16

Limited Warranty ........................................................................................

17

Inspection and Maintenance Schedule ......................................................

18

Questions?  Concerns?  Comments?  Please call (800) 821-0086 (US and Canada) or

(585) 924-6262 (outside US).

Summary of Contents for Free Standing PIVOT PRO





















Reviews: