background image

Thank you very much for choosing an Gorlitz product!

For future reference, please complete the owner’s record below:

Serial Number/Lot Date Code: ____________________________________

Purchase Date: ________________________________________________

Save the receipt, warranty, and this manual. It is important that you read the 

entire manual to become familiar with this product before you begin using it.
This drain cleaner is designed for certain applications only. Gorlitz Sewer & 

Drain Inc. is not responsible for issues arising from modification or improper 

use of this product such as an application for which it was not designed. We 

strongly recommend that this product not be modified and/or used for any 

application other than that for which it was designed.
For technical questions, please contact via emailing to 

sales@gorlitz.com

.

DO NOT ATTEMPT TO OPERATE ANY DRAIN CLEANING MACHINE UNTIL YOU 

HAVE READ AND THOROUGHLY UNDERSTAND ALL INSTRUCTIONS, RULES, ETC.  

CONTAINED IN THIS MANUAL.  FAILURE TO COMPLY CAN RESULT IN ACCIDENTS 

INVOLVING FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY.  MAINTAIN OWNERS 

MANUAL AND REVIEW FREQUENTLY FOR CONTINUING SAFE OPERATION.

WARNING

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

ELECTRIC SHOCK RESULTING IN DEATH CAN OCCUR IF YOU PLUG THIS MACHINE 

INTO AN IMPROPERLY WIRED OUTLET. IF THE GROUND WIRE IS ELECTRIFIED, 

YOU CAN BE ELECTROCUTED BY JUST TOUCHING THE MACHINE, EVEN WHEN 

THE POWER SWITCH IS OFF. A GROUND FAULT CIRCUIT INTERRUPTER WILL NOT 

PROTECT YOU IN THIS SITUATION. USE A UL LISTED TESTER TO DETERMINE IF 

THE OUTLET IS SAFE.

DO NOT OPERATE POWER TOOLS IN EXPLOSIVE ATMOSPHERES, SUCH AS IN THE 

PRESENCE OF FLAMMABLE LIQUIDS, GASES, OR DUST. POWER TOOLS CREATE 

SPARKS WHICH MAY IGNITE THE DUST OR FUMES.

ONLY WEAR LEATHER GLOVES. NEVER USE ANY OTHER TYPE OF GLOVE SUCH AS 

CLOTH, RUBBER, OR COATED GLOVES. NEVER GRASP A ROTATING CABLE WITH A 

RAG.  THESE ITEMS COULD BECOME WRAPPED AROUND THE CABLE AND CAUSE 

SERIOUS INJURY.

ALWAYS WEAR SAFETY GLASSES AND RUBBER SOLED, NON-SLIP SHOES. USE OF 

THIS SAFETY EQUIPMENT MAY PREVENT SERIOUS INJURY.

DO NOT OVERSTRESS CABLES.  OVERSTRESSING CABLES MAY CAUSE TWISTING, 

KINKING, OR BREAKING OF THE CABLE AND MAY RESULT IN SERIOUS INJURY.

This product can expose you to chemicals including lead, which is known to the 

State of California to cause cancer and birth defects or other reproductive harm. For 

more information go to 

www.P65Warnings.ca.gov.

1                                                                                        Gorlitz Operating & Maintenance Manual

Summary of Contents for GO 15 Series





























Reviews: