background image

8

13

1.  UNCOIL CABLE TO BE INSTALLED AND LAY IN 

A STRAIGHT LINE ON THE FLOOR.

2.  PASS A SHORT SECTION OF ANCHOR CABLE 

THROUGH DRIVE ARM.

3.  SLIDE CABLE CONNECTORS TOGETHER AND 

FASTEN BOTH CAP SCREWS.

4.  DRIVE ARM MUST TURN COUNTER 

CLOCKWISE (FACING MACHINE) WHEN 

STARTING TO INSTALL CABLE.

5.  LAY OUTER CABLE TURNS BY HAND TO FILL 

REEL PROPERLY.

6.  START MACHINE.
7.  FEED REMAINING CABLE INTO REEL.
8.  STOP MACHINE OCCASIONALLY TO CHECK 

DISTRIBUTION AND REPOSITION CABLE IF 

NEEDED.

9.  ATTACH CUTTING TOOL OF YOUR CHOICE.

IF YOU ARE USING OUR POWER CABLE FEEDER AND PULLER, DO NOT ALLOW TO PASS 

ANY CABLE ENDS OR CABLE CONNECTORS THROUGH FEEDER, AS IT MAY DAMAGE IT.

8

13

HOW TO INSTALL A NEW CABLE

MODEL GO 68HD, GO 68, GO 62 SERIES

MODEL GO 50 SERIES

1.  UNCOIL CABLE TO BE INSTALLED AND LAY IN 

A STRAIGHT LINE ON THE FLOOR.

2.  MAKE SURE DRIVE ARM ROTATES FREELY.
3.  FEED CABLE WITH INSTALLED CABLE END 

THROUGH DRIVE ARM.

4.  SCREW CABLE END INTO REEL CONNECTOR.
5.  FASTEN REEL CONNECTOR TO REEL WITH 

BOLT.

6.  DRIVE ARM MUST TURN COUNTER 

CLOCKWISE (FACING MACHINE) WHEN 

STARTING TO INSTALL CABLE.

7.  LAY OUTER CABLE TURNS BY HAND TO FILL 

REEL PROPERLY.

8.  START MACHINE.
9.  FEED REMAINING CABLE INTO REEL.
10.  STOP MACHINE OCCASIONALLY TO CHECK 

DISTRIBUTION AND REPOSITION CABLE IF 

NEEDED.

11.  ATTACH CUTTING TOOL OF YOUR CHOICE.

MODEL GO 380/250 SERIES, GO 15

1.  UNCOIL CABLE TO BE INSTALLED AND LAY IN 

A STRAIGHT LINE ON THE FLOOR.

2.  MAKE SURE DRIVE ARM ROTATES FREELY.
3.  FEED CABLE THROUGH DRIVE ARM.
4.  DRIVE ARM MUST TURN COUNTER 

CLOCKWISE WHEN INSTALLING CABLE.

5.  START MACHINE.
6.  FEED REMAINING CABLE INTO DRUM 

ALLOWING ADEQUATE LENGTH OF EXPOSED 

CABLE TO ATTACH FLEXIBLE LEADER 

(ELEPHANT TRUNK) WHEN APPLICABLE.

7.  INSTALL CABLE END AND CUTTING BLADE 

(AVAILABLE ONLY FOR 3/8” DIA. CABLE) AND/

OR MAKE CABLE BENDS OF YOUR CHOICE.

Gorlitz Operating & Maintenance Manual                                                                                          8

Summary of Contents for GO 15 Series





























Reviews: