background image

ATTENTION                                                                                                                                                                         

 

Do not disassemble the device. Do not touch before unplugging the power supply if the device is 
damaged, the power supply cables are not isolated or the isolation is damaged. 

 

All wireless data transferring devices produce interference that may affect other devices which are 
placed nearby. 

 

The device may be connected only by qualified individuals. 

 

The device must be firmly fastened in the predefined location. 

 

The device is susceptible to water and humidity. 

 
INSTRUCTIONS OF SAFETY                                                                                                                                                   

 

This chapter contains information on how to operate “G7S” safely.   

 

BY following these requirements and recommendations you will avoid dangerous situations. You must 
read these instructions carefully and follow the strictly before operating the device!   

 

The device uses a 8V-32V DC power supply. The nominal voltage is 12V DC. It is advised to transport 
the device in an impact-proof package.   

 

Before usage, the device should be placed so that its LED indicators are visible, which show what status 
of operation the device is in.   

 

When connecting the connection cables to the vehicle, the appropriate jumpers of the power supply of 
the vehicle should be disconnected.   

 

Before dismounting the device from the vehicle, the connection must be disconnected. 

 

LEGAL NOTICE                                                                                                                                                                           

 

Copyright ©  2014 Gosafe. 

 

All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this 
document in any form without the prior written permission of Gosafe is prohibited. 

 

Other products and company names mentioned herein may be trademarks or trade names of their 
respective owners. 

 
INTRODUCTION 

 

With accurate GPS location performance, a robust programmable rules engine, 3 axis accelerometer 
for measuring driver behavior and vehicle impacts, geo-fencing, messaging and much more, the G7S is 
designed for powerful solution deployment.   

 

The G7S is powered by over-the-air device management and maintenance system, (Programming, 
Updates, and Logistics System). FOTA (Firmware update over the air), GSM Jamming detection and 156 
hardware based geo-fences makes this the perfect choice for superior safety and security of your 
vehicle. 

 
 
 

Summary of Contents for G7S












Reviews: