- 11 -
**When the SAFETY KEY is taken off and then replaced, it will not make reposition
action any where it is.
You need to press start key to perform the incline to reposit it.
When power on, it will not make reposition action any where it is. You need to press start key to perform the
incline to reposit it.
Under Start/Ready position, press stop key and keep it for 5 seconds, it will make reposition action
any where it is.
**During perform any program, if press stop key, the program will stop. If users want to continuously
perform the program, press start key or again press stop key to leave the program and back to start/ready
status.
IV.
Edit Mode：
1.
Under Start/Ready position, press
Mode
to choose Manual and Program mode by press +/- key.
2.
Program Mode
：
Press +/- key to edit the Program (P1~P8) ,and the PROGRAM window will flash,
the LCD window will show P1~P8 to edit , you can press +/- key to edit. Press ENTER to enter the
TIME edit, the Program pre-set value is 30min, Range is 20~99min, STEP is 1.After edit, press
ENTER or START to start the machine. If you press START directly during edit, the rest un-edited
functions are pre-set. During edit, INCLINE and SPEED window will display first level value.
The matrix window will display the picture.
3.
WARM UP and COOL DOWN function: During WARM UP or Program position, change speed or
inclination, the value will increase or decrease in the next level. COOL DOWN is not affected and
STOP is the only function which can be carried out.
4.
PROGRAM
has
30
levels in all. The three anterior are
WARM UP
, the three later
are
COOL DOWN
. Everyone is
3
minutes. The setting time except anterior and later
which mean 6 minutes will be execute averagely by surplus 24 levels.
5.
9 HOLES mode have not functions of WARM UP
or
COOL DOWN
. When distance is equal to
3.5KM
, the motor will stop, the INCLINE is
0
and displays
” End”
.
V.
Program Operation and Instruction：
Manu Mode
1.
When press START
,
it will
begin to count down for 3 seconds, after that, the motor will start , the
speed will start at 0.8KPH
（
0.5MPH
）
. The matrix window goes contrarotate like along playground,
every circle is 0.4KM (0.25MIL).
2.
Speed STEP is 0.1, you can press SPEED UP/DOWN key to select
（
the speed UP/DOWN step is
0.1
）
, or press speed instant key 1
、
2
、
4
、
6
、
8
、
10 to select .
3.
Incline STEP is 1, you can press INCLINE UP/DOWN key to select
（
incline UP/DOWN step is 1
）
,
or press incline instant key 2
、
4
、
6
、
8
、
10
、
12 to select.
4.
TIME set or not set:
(1) When TIME has bee set, the window will display a time value counting down from the target
value, when the time reaches 0:00, the treadmill will stop automatically.
(2) When TIME hasn’t been set, the window will display the exercise time, when the time reaches
99:00, the treadmill will stop automatically.
5.
When you press
Mode key
, it will switch among
SPEED, DISTANCE and CALORIES. No
switch among INCLINE, PULSE or WEIGHT and only displays INCLINE. When you receive
PULSE massage, the display will give priority to PULSE. When you receive heartbeat value, the
heartbeat window will display the value.
6.
Press Stop when the motor is working, the motor will stop and the incline motor will stop, the
window will display Stop; If you press START key again, the motor will start after 3-seconds
countdown , the speed will be keep at the same before stop , and the incline will be increased to the
set height before stop .
Summary of Contents for TREADMILL 304
Page 1: ...TREADMILL 304 OWNER S MANUAL...
Page 21: ...20...
