Grace GMQ Pro Manual Download

Page: 30 / 31

(ID: 040708)

Quilt Top

Quilt Batting

Quilt Backing

1st

2nd

3rd

4th

• First, remove your Cone Thread Holder off

your carriage before you can slide your machine

inside. • You may have to take your cone

thread guides out.

• Remove the take up rail with fabric and rest it

on the bottom of the rail mount ends.

• Slide your machine into the carriage from the

back. It will might be easier if your carriage is all

the way to the front, so it does not slide with you.

• Once you have your machine on you can put

your Cone Thread Holder back on as well as

putting your rail back in place.

• Slide the carriages all the way to the left (non-

ratchet wheel side).

• Put the left end of the take up rail with fabric

through the throat of the machine (feeding the

fabric layers under the raised presser foot).

•Put the take up rail back in the slots or the

mounts.

STEP: 5 PUTTING YOUR MACHINE/ CARRIAGE ONTO FRAME

Parts Needed: 1- Frame (assembled)

1- Sewing Machine

(When you have finished using your machine for a little bit, you will want to park it to one side of your frame.)



Center the batting on the

rail and attach one end of

the batting using the fabri-fast

tubing. (NOTE: Fabri-Fast

tubing will work with most

batting, however, if the batting is

too thick to squeeze into the slot, you may

tape the batting to the rail to keep it in place).



Roll the batting onto rail, being sure to roll the

proper direction so that it, like the quilt top, comes off the rail

from the bottom when unrolling.

STEP 4:

ATTACHING YOUR QUILT LAYERS TO THE

TAKE-UP RAIL



Take the edge of the quilt backing and pin it along

the straight line of the take up rail leader in a smooth

manner, without stretching your fabric.



Next, bring your batting up in between the 3rd

rail and 2nd rail and drape over the backing. Lay it

along the pin line of your backing on the take up rail

cloth leader.



Finally, bring the quilt top up over the

backing and batting and lay it over the batting along the pin line on the take up rail cloth leader. Pin

your top and batting along the same line as your backing in a smooth manner.

Summary of Contents for GMQ Pro
































Search results

Summary of Contents for GMQ Pro

Reviews:

Related manuals for GMQ Pro

Brands by name

Popular brands

Grace GMQ Pro, Manual

Search results

Summary of Contents for GMQ Pro

Reviews:

Related manuals for GMQ Pro

Brands by name

Popular brands