Channel
Data
Function
CH1
0 -10
None
CH4 – CH8 allowed
11 - 50
A1
51 - 100
A2
101 - 150
A3
151 - 200
A4
201 - 255
A5
CH2
0 - 39
Automatic Operation
40 – 49
Red
50 – 59
Green
60 - 69
Blue
70 - 79
Yellow
80 - 89
Cyan
90 - 99
Purple
100 - 109
White
110 - 119
Red + Green
120 - 129
Red + Blue
130 - 139
Red + White
140 - 149
Green + Blue
150 - 159
Green + White
160 - 169
Blue + White
170 - 179
Red + Green + White
180 - 189
Red + Blue + White
190 - 199
Green + Blue + White
200 - 209
Red + Green + Blue
210 - 255
Red + Green + Blue + White
CH4
Dim
CH5
Red
CH6
Green
CH7
Blue
CH8
White
III. DMX Channel List:
(For use with controller)
II.Menu:
When you press the “MENU” switch there are the following
options:
1. [D001]: This is the lights DMX address. You can press “UP” or “DOWN” to set it
from [D000] up to [D512] and press “ENTER” to confirm it. This function allows you
to put the light fixture in DMX mode so that you may use a controller if needed.
2. [IP01]: This is the lights IP address. You can press “UP” or “DOWN” to set it from
“IP01” up to “IP64” and press “ENTER” to confirm it.
3. [A1xx]: These are the static colors. You can press “UP” or “DOWN to set it from
[A1.01] up to [A1.19] and press “ENTER” to confirm it. These are preset colors.
4. [A2xx]: This is the color alternating effect. You can press “UP” or “DOWN to set the
speed from [A2.01] up to [A2.32] and press “ENTER” to confirm it. This mode
alternates between colors automatically.
5. [A3xx]: This is the color fade out and color fade in effect. You can press “UP” or
“DOWN to set the speed from [A3.01] up to [A3.19] and press “ENTER” to confirm it.
6. [A4xx]: This is the sound activated strobe effect. You can press “UP” or “DOWN” to
set it from [A4.01] up to [A4.19]. When the display is flickering, you can press “UP” or
“DOWN” to change the sensitivity of the sound activated effect from [01] to [04] and
press “ENTER” to confirm it.
7. [A5xx]: This is the automatic strobe effect. You can press “UP” or “DOWN” to set it
from [A5.01] up to [A5.19] and press “ENTER” to confirm it. When the display is
flickering, you can press “UP” or “DOWN” to change the speed of the strobe effect
from [01] to [32] and press “ENTER” to confirm it.
8. [A6xx]: This is all modes (except sound active mode). You can press “UP” or
“DOWN” to set it from [A6.01] to [A6.19] to change the speed, and press “ENTER” to
confirm it. This mode will alternate through all of the effects.
9. [A7xx]: This is the preset static color strobe effect. You can press “UP” or “DOWN”
to set it from [A7.01] to [A7.19] to change which preset static color strobe is working,
and press “ENTER” to confirm it.
10. [Rxxx] This is the red color dim. You can press “UP” or “DOWN” to set it from
[R000] to [R255] to dim the red color, and press “ENTER” to confirm it.
11. [Gxxx] This is the green color dim. You can press “UP” or “DOWN” to set it from
[G000] to [G255] to dim the green color, and press “ENTER” to confirm it.
12. [Bxxx] This is the blue color dim. You can press “UP” or “DOWN” to set it from
[B000] to [B255] to dim the blue color, and press “ENTER” to confirm it.
13. [uxxx]: This is the white color dim. You can press “UP” or “DOWN” to set it from
[u000] to [u255] to dim the white color, and press “ENTER” to confirm it.
(For use without controller)
I.Operation
This light has 4 functions:
1. DMX512 with 8 channels
2. Automatic operation
3. Sound Activated
4. Master/slave
Note: in order to use a DMX
controller you must make sure the
back panel is in DMX mode. To do
this press “MENU” until the LED
screen reads [D001], and the press
“ENTER” to confirm.
