5
167-10-97 IS1572
6
8
7
Attaching the Legs
Step 1.
Push
oval
end of the upper
leg sections firmly onto the
four plastic pegs. Hold tube
vertically while pushing in.
Push leg on completely.
Step 2.
Push the leg tips on the
round ends of the lower leg
sections. (The other ends
have a wire.)
Step 3.
Put the wire end of lower
leg sections into the
round
end of the upper leg sections.
Push the sections together
while twisting lower leg slightly.
This will ensure a snug fit.
Step 4.
CHECK:
Lift swing as shown. If legs are
assembled properly, the legs
will dangle from the motor unit
and not fall off.
IF LEG FALLS:
Holding leg vertically, push
leg firmly up while pushing
the motor unit down.
Step 5.
Open the swing legs
completely. Snap plastic leg
braces onto outside of legs.
The plastic pins inside the
ends of the braces will fit into
the dimples on the legs.
It may be necessary to spread
the legs as shown.
Do not use
swing without the leg
braces.
Wire end
Dimple
Hold
tube
vertically
Flattened
side
Plastic
peg
Attaching the Hanger
Step 1.
With crossbar of hanger
toward front of the motor unit
,
line up holes in hanger brackets
with holes on the sides of motor
unit.
Step 2.
Insert screws into both brackets
as shown. Fasten with acorn
nuts using the enclosed hex
wrench. Tighten nuts firmly with
hex wrench and screwdriver.
Adjusting the Handle
To bring infant carrier handle
from resting position into posi-
tion for carrying or swinging,
first
set the carrier down
.
Then push down on center of
handle, and rotate the handle
forward until it clicks into the
locked position.
To return the handle to resting
position, first
set the carrier
down.
Then push down on
center of handle, and rotate the
handle backward until it clicks
into place.
NOTE: It is normal for the
handle to seem loose in the
resting position.
Using the Tray
Unlatch the tray by squeezing
the two latches under the tray
at the same time, and lift up
tray.
Be careful
not to let tray
hit your baby when lifting or
closing tray.
To latch tray, push down firmly.
Tray must be latched at all
times when baby is in the
swing.
Adjusting the Stand
To change recline of the carrier,
squeeze the adjustment wire
and move to desired position.
To adjust for rocking, move the
adjustment wire to the highest
position.
Do not
change recline with baby in
infant carrier.
Be aware that infant move-
ment or rocking may cause
the infant carrier to move on
a table.
Push down
on center
of handle
Push down
on center
of handle
Different uses for infant carrier...
Cuddler
Carrier
Feeder
...or as a Rocker.
Hanger
Notch
Step 2.
Lift top frame of cradle, and
turn handle so that it lines up
with the plastic hinges.
Step 3.
Snap handle and hinges
together to lock.
Be sure
handle is locked into the
plastic hinges.
Step 4.
Place cradle in hanger.
Be sure handle notches are
seated in the hanger
.
Step 5.
Place your child in the cradle.
Step 6.
Set the control switch between
the low and medium positions.
Your cradle will swing properly
only in the lower range.
Step 7.
Give cradle a push to start the
swinging motion.
Using the
Infant Carrier
Lift carrier in and out of swing.
Do not adjust
the handle while carrier is on
swing.
Step 1.
With baby out of swing
, open
the battery compartment by
gently pressing on the lid at the
ridged area and lifting the lid.
Step 2.
Insert four D cells. Be sure
the batteries are put in correctly.
(Swing will not run if batteries
are put in backwards.)
Step 3.
Snap the lid closed.
Using the Cradle
Not intended
for use as a night-time bed or
car bed.
REMOVE LAW TAGS FROM
CRADLE PAD AND QUILTED
SHEET BEFORE USING THIS
CRADLE.
Step 1.
Cover soft side of cradle pad
with quilted sheet provided.
Installing Batteries
NEVER INSERT OR REMOVE
BATTERIES WITH BABY IN THE SEAT. THEY COULD
FALL ON BABY IF DROPPED!
Round
end
(not oval)
Push
Push
