background image

 

2

309584H

WARNINGS

Equipment Misuse Hazard

Equipment misuse can cause equipment to rupture, malfunction, or start unexpectedly and cause 
serious injury.

Before operating this equipment, read all manuals, tags, and labels including material labels and 
instructions.

Do not expose system to rain. Always store system indoors.

Do not alter or modify equipment.

Do not spray cementcious materials.

Do not exceed maximum working pressure of lowest rated component in your system.

Check equipment daily. Repair or replace worn or damaged parts immediately.

To reduce risk of serious injury, including electric shock and splashing fluid in eyes, follow 

Pressure 

Relief Procedure, page 3

 before servicing the unit.

Do not use hoses to pull equipment.

Route hoses away from traffic areas, sharp edges, moving parts and hot surfaces. Do not expose 
Graco hoses to temperatures above 130 F (55 C) or below -35 F (-37 C).

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, 
state and national guidelines.

Never directly inhale compressed air. Compressed air may contain toxic vapors.

Electric Shock Hazard

To reduce the risk of electric shock:

Be sure sprayer is adequately grounded through electrical outlet.

Use only 3-wire, extension cords.

Make sure ground prongs are intact on sprayer and extension cords.

Do not operate with cover removed.

Turn off sprayer. Follow

 Pressure Relief Procedure, page 3,

 and unplug unit, before removing any 

parts.

Summary of Contents for 245924 A Series













Reviews: