background image

Platform Access Position (826098)

310820H

15

Platform Access Position (826098)

To avoid falling, make sure 
sprayer is on a firm, level, 
non-slippery, secure foundation 
before standing on sprayer 
platform. 

To avoid electrocution, do not 
allow sprayer frame to come in 
contact with live electrical wires. 

To avoid falling, do not over reach 
while standing on sprayer 
platform.

If you are unable to step up to 
sprayer platform, use a stable 
intermediate stepping device. 

The sprayer platform is 
reversible, and can be installed 
facing either direction.

To install the platform, perform 
the following steps:

1

Slide platform guiding 
plate (G) into sprayer 
frame. 

2

Align groove 
underneath 
platform with 
sprayer 
handle (H).

3

Press other end of platform down onto 
opposite end of sprayer frame. Make 
sure frame peg (P) is aligned with slot 
underneath platform.

CAUTION: If the frame peg (P) is not 
aligned with the slot underneath 
platform, the platform will not be fully 
resting on the sprayer frame and will be 
unsafe to stand on.

ti11587a

G

ti11586a

H

ti11612a

P

ti11585a

Summary of Contents for 310820H



















Reviews: