background image

15

307–452

Parts

Ref.
No.

Part No.

Description

Qty.

Ref.
No.

Part No.

Description

Qty.

1

NEEDLE, fluid 
See charts on page 5

1

2

NOZZLE, fluid 
See charts on page 5

1

3

AIR CAP
See charts on page 5

1

4

106–785

BODY, gun 
Includes fittings 22 & 23

1

5

106–719

VALVE, fan adjustment

1

6

105–553

KNOB, fluid adjustment

1

7*

105–554

SPRING, compression, fluid needle 1

8

106–720

GUIDE, needle, fluid

1

9

106–718

NUT, packing, needle

1

10*

106–885

KIT, packing, needle

1

11*

105–608

SPRING, compression, air valve

1

12*

106–731

VALVE, air (needle)

1

13

n

106–732

KIT, packing, air valve

1

14

106–730

TRIGGER

1

15

105–606

SCREW, pivot, trigger

1

16

105–605

SCREW, retaining, trigger

1

17

n

106–729

VALVE, air adjustment

1

18*

105–551

GASKET

1

19*

105–563

O-RING

2

20

BRUSH; not sold separately

1

21

179–764

WRENCH, nozzle

1

22

106–786

FITTING, fluid; includes gasket 
& washer

1

23

106–784

FITTING, air

1

n

Keep these spare parts on hand to reduce down
time.

*

These parts are included in Repair Kit 106–779,

which may be purchased separately.

Summary of Contents for 700N





















Reviews: