Graco Husky 307 F Series Instructions-Parts List Manual Download | Manualshive

Page: 34 / 36

background image

34

308553ZAE

Technical Data

Pumps with TPE or Buna-N Diaphragms

Maximum fluid working pressure ......... 100 psi (0.7 MPa, 7 bar)
Air pressure operating range20 to 100 psi (0.14 to 0.7 MPa, 1.4
to 7 bar)
Maximum air consumption ...................... 5.5 SCFM (see chart)
Maximum free flow delivery ...........................7 gpm (26.5 l/min)
Maximum pump speed ................................................. 330 cpm
Maximum suction lift ............. 12 ft (3.7 m) dry; 21 ft (6.4 m) wet
Maximum size pumpable solids .......................1/16 in. (1.6 mm)
Sound power level,

at full flow: (100 psi [0.7 MPa, 7 bar) .................... 85 dBa

Sound power level,

at 70 psi (0.48 MPa, 4.8 bar) and 1 gpm (3.8 lpm) 78 dBa

Operating temperature range.................................. 40 to 150



F

(4.4 to 65.5



C)

Air inlet size ..................................................................1/4 npt(f)
Fluid inlet and outlet size. .............................................3/8 npt(f)
Wetted Parts ................... Vary by model. See pages 28 and 30.

Acetal models include acetal with conductive sst fibers.

Non-wetted external parts. acetal, polyester (labels), glass-filled
polypropylene with conductive SST fibers, 303, 304 and 316
stainless steel
WeightAcetal Pumps: 5.25 lb (2.4 kg)

Polypropylene Pumps: 4.75 lb (2.2 kg)

* Sound power level measured per ISO standard 9614-2.

Santoprene

®

is a registered trademark of the Monsanto

Company.

0

20

40

60

80

100

120

0

1

2

3

4

5

6

7

8

(7.6)

(15.2)

(22.7)

(30.3)

(2.8)

(1.4)

(4.2)

280
(85.3)

240
(73.2)

200
(61.0)

160
(48.8)

120
(36.6)

80

(24.4)

40

(12.2)

0

0

20

40

60

80

100

0

5

10

15

20

25

(1.52)

(3.05)

(4.57)

(6.1)

(7.62)

(5.6)

(7.0)

(8.4)

(3.8)

(11.4)

(19.0)

(26.5)

Example of Finding Pump Air Consumption and Air Pressure at a Specific Fluid
Delivery and Discharge Head: To supply 3 gpm (11.4 liters) fluid flow (horizontal scale
at 50 psi (3.5 bar) discharge head pressure (vertical scale) requires 3 scfm (.084 m

³

/min

air consumption at 70 psi (4.9 bar) inlet air pressure.

feet
(meters)

psi
(bar)

100 psi air
(7 bar)

70 psi air
(4.9 bar)

40 psi air
(2.8 bar)

20 psi air
(1.4 bar)

3 scfm (0.084
m³/min)

5 scfm (0.14
m³/min)

PUMP DISCH

ARGE HEAD

PERCENTAGE OF

FLOW DECREASE

FLUID FLOW GPM (lpm)

KEY

FLUID PRESSURE AND FLOW

SCFM AIR CONSUMPTION

TEST CONDITIONS
Pump tested in water with inlet submerged.

PUMPING RATE DECREASE AT DIFFERENT SUCTION LIFTS

EXAMPLE: At a suction lift of 10 ft (3.05 m), the pump flow rate will be decreased by 20 percent.

SUCTION LIFT IN FEET (METERS)

Tel: 866-777-6060
Fax: 866-777-6383

Springer Pumps, LLC

Website: www.springerpumps.com

Int'l: +001 267 404 2910

«
...
32
33
34
35
36
»

Summary of Contents for Husky 307 F Series





































Reviews:

No comments

Related manuals for Husky 307 F Series

Brand: Sanden Pages: 26

Brand: SAHP Pages: 41

Zoneline AZ85H09DAC

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: dafi Pages: 12

Brand: York International Pages: 87

Brand: Danfoss Pages: 22

Brand: Waterous Pages: 10

MULTIDRAIN UV 305-1

Brand: Pentair Jung Pumpen Pages: 40

Brand: Oase Pages: 16

Brand: Quantum Pages: 36

General Pump EV Series

Brand: Interpump Pages: 19

OKCE 100 NTR/2,2kW

Brand: Dražice Pages: 11

Brand: Godiva Pages: 61

Brand: Vetus Pages: 16

EVOPLUS SMALL 60/180 M

Brand: DAB Pages: 260

Brand: A.O. Smith Pages: 18

Wittig RFW 150 DV

Brand: Gardner Denver Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands