Graco Husky 307 F Series Instructions-Parts List Manual Download | Manualshive

Page: 5 / 36

background image

308553ZAE

5

Installation

Grounding

To reduce the risk of static sparking, ground the pump and
all other equipment used or located in the pumping area.
Check your local electrical code for detailed grounding
instructions for your area and type of equipment.

Ground all of this equipment:



Pump: Attach a ground wire (Y) to the grounding strip
(112) with the screw (28), lockwasher (29) and nut
(27), as shown in F

. 1. Connect the clamp end of the

ground wire to a true earth ground. Order Part No.
222011 Ground Wire and Clamp.

NOTE: When pumping conductive flammable fluids with
a polypropylene pump, always ground the fluid system.
See the WARNING at left. F

recommended methods of grounding flammable fluid
containers during filling.

F

IG

. 1

____________________



Air and fluid hoses: Use only electrically conductive
hoses.



Air compressor: Follow the manufacturer’s
recommendations.



Solvent pails used when flushing: Follow your local
code. Use only metal pails, which are conductive. Do
not place the pail on a non-conductive surface, such
as paper or cardboard, which interrupts the grounding
continuity.



Fluid supply container: Follow your local code.

WARNING

FIRE AND EXPLOSION HAZARD
This pump must be grounded. Before
operating the pump, ground the system as
explained at right. Also read the section
FIRE AND EXPLOSION HAZARD on
page 3.

The acetal pump contains stainless steel fibers, which
makes the wetted parts conductive. Attaching the
ground wire to the grounding strip grounds the air
motor and the wetted parts.

The polypropylene pump is not conductive.

When pumping conductive flammable fluids, always
ground the entire fluid system by making sure the fluid
system has an electrical path to a true earth ground
(see F

. 4 through F

. 7). Never use a

polypropylene pump with non-conductive flammable
fluids as specified by your local fire protection code.

US Code (NFPA 77 Static Electricity) recommends a
conductivity greater than 50 x 10

-12

Siemans/meter

(mhos/meter) over your operating temperature range
to reduce the hazard of fire. Consult your fluid supplier
to determine the conductivity or resistivity of your fluid.
The resistivity must be less than 2 x 10

12

ohm-centimeters.

Y

112

27
29

28

01432B

Tel: 866-777-6060
Fax: 866-777-6383

Springer Pumps, LLC

Website: www.springerpumps.com

Int'l: +001 267 404 2910

«
...
3
4
5
6
7
...
»

Summary of Contents for Husky 307 F Series





































Reviews:

No comments

Related manuals for Husky 307 F Series

Brand: Gardena Pages: 182

Aquarea WH-MDF06E3E5 series

Brand: Panasonic Pages: 36

Brand: Ultranatura Pages: 24

Brand: Gardena Pages: 16

Brand: Gardena Pages: 9

Brand: Gardena Pages: 11

13000 aquasensor

Brand: Gardena Pages: 14

Brand: Valeo Pages: 88

Brand: Valdemar Energy Pages: 61

Odyssey ODYR-25-1

Brand: Dakota Digital Pages: 8

Brand: AmeriWater Pages: 16

American Pride ACNF Series

Brand: Amana Pages: 8

Brand: Kospel Pages: 40

Johnson Pump CombiProLine OH3

Brand: SPX FLOW Pages: 67

Brand: Gardner Denver Pages: 27

Brand: AMT Pages: 8

Brand: Rietschle Pages: 17

Brand: Endress Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands