background image

TECHNICAL DATA

All inlets : 

 

Material Outlet :

 

 or 

 with outlet adapter removed

Air Motor : 1 HP; 2800 RPM maximum

Air Requirements : 25 to 30 CFM at 100 psi 

 bar) continuous operation

Wetted Parts : Stainless steel, steel, carbon steel; PTFE, Nylon,

Viton

SERVICE INFORMATION

THE GRACO WARRANTY

Listed below by the assembly changed are ADDED and
DELETED parts.

ASSEMBLY PART

 PART

CHANGED STATUS

NO. NO.

NAME

I

207-388
Mixer to

S e r i e s   F

DELETED
ADDED
DELETED

ADDED
DELETED
ADDED

2 8

2 9

3 1

Lever

170-747

Lever

207-394

Lever

217-561

Lever

207-875

V a l v e
V a l v e

NOTE: ADDED parts are NOT interchangeable with

DELETED parts.

*When ordering replacement ball valve on Series E or

earlier mixers, order Kit No. 217-412 which includes
two new style ball valves and new style actuating

lever.

 Inc. warrants all equipment manufactured by it and bearing its

name to be free from defects in material and workmanship under

normal use and service. This warranty extends to the original

purchaser for a period of 12 months from the date of purchase and ap-
plies only when the equipment is installed and operated in
accordance with written factory recommendations. This warranty
does not cover damage or wear which, in the reasonable judgment of

  a r i s e s   f r o m   m i s u s e ,   a b r a s i o n ,   c o r r o s i o n ,   n e g l i g e n c e ,   a c c i d e n t ,

substitution of non-Grace parts, faulty installation or tampering.

This warranty is conditioned upon the prepaid return of the equipment
claimed to be defective for examination by 

 to verify the claimed

defect. If the claimed defect is verified, 

 will repair or replace

free of charge, any defective parts. The equipment will be returned to
the original purchaser transportation prepaid. If inspection of the

equipment does not disclose any defect in workmanship or material,
repairs will be made at a reasonable charge and return transportation

w i l l   b e   c h a r g e d .

THIS LIMITED WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF
ANY OTHER WARRANTIES (EXPRESS OR IMPLIED) INCLUDING

WARRANTY OF MERCHANTABILITY OR WARRANTY OF

FITNESS FOR A PARTICULAR PURPOSE AND OF ANY 
CONTRACTUAL LIABILITIES INCLUDING PRODUCT LIABILITIES
BASED ON NEGLIGENCE OR STRICT LIABILITY. EVERY FORM OF
LIABILITY FOR DIRECT, SPECIAL OR CONSEQUENTIAL
DAMAGES OR LOSS IS EXPRESSLY EXCLUDED AND DENIED.

EQUIPMENT NOT COVERED BY GRACO WARRANTY. Accessories
or components of equipment sold by 

 that are not manufactured

by 

 (such as electric motors, switches, hose, etc.) are subject to

the warranty, if any, of their manufacturer. 

 will provide

purchaser with reasonable assistance in making such claims.

Factory 

 

Dallas, Detroit, Los Angeles, West 

 

Subsidiary and Affiliate 

 

England; Switzerland; France; Germany; Hong Kong; Japan

GRACO INC. P. 0. Box 1441 MINNEAPOLIS, MN 5544011444

PRINTED IN U.S.A. 

 4-67 

Revised 

Summary of Contents for Hydra-Cat 207-388 F













Reviews: