background image

2

308511

Table of Contents

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Service

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Warranty

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Information

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

D

This equipment is for professional use only.

D

Read all instruction manuals, tags, and labels before operating the equipment.

D

Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

D

Do not alter or modify this equipment.

D

Check equipment daily. Repair or replace worn or damaged parts immediately.

D

Do not exceed the maximum working pressure stated on the equipment or in the Technical Data
for your equipment. Do not exceed the maximum working pressure of the lowest rated component
in your system.

D

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data
 section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

D

Handle hoses carefully. Do not pull on hoses to move equipment.

D

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 66

_

C (150

_

F) or below –40

_

C (–40

_

F).

D

Wear hearing protection when operating this equipment.

D

Do not move or lift pressurized equipment.

D

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

Summary of Contents for Hydra-Clean 308511J











Reviews: