background image

11

308–333

Parts

Part No. 236–066
Wall Mount Pump

Ref.
No.

Part No.

Description

Qty.

1

186–727

BRACKET, wall mounting

1

2

223–843

PRESIDENT PUMP; stainless steel
See manual 308–106 for parts

1

5

223–160

FLUID FILTER; stainless steel
See manual 307–273 for parts

1

6

235–992

BALL VALVE; 3/8 npt x 1/4 npt(mbe);
stainless steel; 
See manual 306–861 for parts

1

7

188–089

NIPPLE; 3/8 npt x 3/8–18.6 sf;
stainless steel

1

8

179–749

MANIFOLD, air; 1/2 npt inlet;
two 1/2 npt outlets

1

9

156–877

NIPPLE; 1/2 npt; 2/5” (63.5 mm)

3

10

104–267

AIR REGULATOR
0–125 psi (0–0.9 MPa, 0–9 bar) range
See manual 308–167 for parts

2

11

155–470

UNION, adapter, 90

;

1/2 npt(m) x 1/2 npsm(f) swivel

1

12

101–180

GAUGE, air pressure;
0–200 psi (0–1.4 MPa, 0–14 bar)

2

13

218–093

HOSE, air; buna-S; 1/2” (13 mm) ID;
cpld 1/2 npt(mbe); 22” (559 mm) long

1

Ref.
No.

Part No.

Description

Qty.

14

222–297

UNION, adapter, 45

;

1/2 npt(m) x 1/2 npsm(f) swivel

1

15

158–491

NIPPLE; 1/2 npt; 1.625” (41 mm) long 1

16

107–142

VALVE, air, bleed-type;
1/2 npt(m x f)

1

18

166–999

ELBOW, street, reducing;
1/2 npt(n) x 1/4 npt(f)

1

19

162–453

NIPPLE; 1/4 npt x 1/4 npsm

1

20

236–076

HOSE, suction, fluid; nylon;
3/4 npt(mbe); 3/4” (19 mm) ID;
6 ft (1.82 m) long

1

21

188–867

TUBE, suction; 3/4 npt(m x f);
stainless steel

1

22

112–192

ELBOW, fluid intake; 3/4 npt(fbe);
stainless steel

1

23

188–595

BRACKET, pump mounting

1

25

100–016

LOCKWASHER, spring; 1/4”

2

26

100–270

CAPSCREW, hex hd;
1/4–20 x 5/8” (16 mm) long

2

28

100–509

PLUG, pipe; 1/4 npt

2

32

235–208

THUMBSCREW; 5/16–18 unc;
1” (25 mm) long

1

34

188–940

ADAPTER, bung; stainless steel

1

35

102–254

SCREW, hex hd; 1/4–20 x 
7/8 (22 mm) long

2

39

157–416

UNION, adapter, 90

; 1/2 npt(f) x 

1/2 npsm(f)

1

50

206–994

THROAT SEAL LIQUID (not shown)

1

Technical Data

Category

Data

Maximum Working Pressure

3600 psi (25.0 MPa, 250 bar)

Maximum Incoming Air Pressure

120 psi (0.84 MPa, 8.4 bar)

Ratio

30:1

Wetted Parts: Pump

See manual 308–106

Wetted Parts: Fluid Filter

See manual 307–273

Wetted Parts: Suction Hose and Tube

Nylon, 304 Stainless Steel

Wetted Parts: Fluid Fittings

304 and 316 Stainless Steel

Manual Change Summary

This manual was updated to include the changes from PCN C.

Model 236–068 is obsolete and has been removed from this manual.

Summary of Contents for President 236-066













Reviews: