background image

Parts 

44

311189L

Flow Control Regulator

Part No. 249849

Parts included in Regulator Service Kit 15G843 
(purchase separately).

Parts included in Sensor Service Kit 15G867 
(purchase separately).

Ref. 
No.

Part No. Description

Qty

.

1

102980 NUT, full hex

1

2



111316 PACKING, o-ring

1

3

112698 ELBOW, male, swivel

1

4

117610 O-RING

1

5

FASTENER, shcs, 10-32X.5

12

6

PLATE, fluid, regulator

1

7

15F799 PLATE, air, regulator

1

9

SEAT, regulator

1

10

RETAINER, seat

1

11

HOUSING, flow control

1

12

SPACER, regulator

1

13

NEEDLE, regulator

1

14

BRACKET, flow control

1

15

15F806 PLUG, regulator

1

16

168881 GASKET, non-metallic

1

17

178321 DIAPHRAGM, regulator

1

18

249179 BOARD, circuit assembly

1

19

120013 VALVE, proportional, V/P

(includes 19a and 19b)

1

19a

SCREW; M3 x 0.5 x 44 mm
mounting shcs

2

19b

106560 O-RING, mounting, size 007

2

20

SENSOR, flush mount

1

21

107295 SCREW, mach, pan hd

4

22

104765 PLUG, pipe headless

1

23

192387 PIN, dowel

2

24

15G613 HARNESS, flow control

1

4

6

20

7

3

5

19

18

21

5

14

1

24

22

5

23

13

10

9

12

17

16

11

15

TI7153a

2

19b

19a

Flow
direction

1

2

2

3

2

Torque to 8-10 in-lbs (0.9-1.1 N•m)

Torque to 30-40 in-lbs (3.4-4.5 N•m)

Torque to 5-7 in-lbs (0.6 -0.8 N•m)

1

2

3

Summary of Contents for ProMix Auto Series

















































Reviews: