background image

Graco Standard Warranty

312879E

11

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to 
be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the 
exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months 
from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty 
applies only when the equipment is installed, operated and maintained in accordance with Graco’s written 
recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or 
wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, 
negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for 
malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, 
equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or 
maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco 
distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of 
charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If 
inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a 
reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, 
INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A 
PARTICULAR PURPOSE

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer 
agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost 
sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for 
breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS 
OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO

. These items sold, but not manufactured by 

Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco 
will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco 
supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, 
whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and 
legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn 
up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi 
que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, 
directement ou indirectement, avec les procédures concernées.

Summary of Contents for T-Max Applicator 17Z054













Reviews: