Warnings
3A8108A
5
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
Do not operate the unit when fatigued or under the influence of drugs or alcohol.
•
Do not exceed the maximum working pressure rating of the lowest rated system
component. See
Technical Specifications
in all equipment manuals.
•
Do not leave the work area while equipment is energized or under pressure.
•
Turn off all equipment and follow the
Pressure Relief Procedure
when equipment is not
in use.
•
Check equipment daily. Repair or replace worn or damaged parts immediately with
genuine manufacturer’s replacement parts only.
•
Do not alter or modify equipment. Alterations or modifications may void agency approvals
and create safety hazards.
•
Make sure all equipment is rated and approved for the environment in which you are using
it.
•
Use equipment only for its intended purpose. Call your distributor for information.
•
Keep children and animals away from work area.
•
Comply with all applicable safety regulations.
ELECTRIC SHOCK HAZARD
Hazardous voltage is present in control box while engine is running.
•
Turn off engine before servicing equipment.
LASER LIGHT HAZARD: AVOID DIRECT EYE CONTACT
Eye exposure to Class IIIa3/3R levels of laser light can potentially present an eye (retinal)
injury hazard, including spot blindness or other retinal injury. To avoid direct eye exposure:
•
Never look directly in to a laser beam or point the beam into the eyes of others, even at long
distances.
•
Never shine the laser at mirror like surfaces which can cause specular reflections of the
beam.
•
Always set the laser at a height and angle that prevents the beam from shining into
people’s eyes.
•
Immediately terminate laser emissions if personnel, animals or reflective objects approach
the beam.
•
Always turn off laser when unattended.
•
Do not remove any warning labels from the laser.
•
Only properly trained laser operators are to use this product.
•
Never allow beams to be aimed toward traffic, vehicles, or heavy equipment. Even when
not damaging at long distances, the high brightness of lasers can distract or disrupt vehicle
operations.
•
Never point a laser at an aircraft or law enforcement personnel. This is considered a felony
in most locations, with the possibility of jail time, heavy fines or both.
•
Do not disassemble laser product. Return to factory for all service procedures.
•
Laser must be turned OFF when cleaning the lens, so as not to create unwanted laser
refraction.
LASER RADIATION HAZARD
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
•
Do not attempt to open or disassemble the laser housing under any circumstances. Doing
so may cause exposure to potentially hazardous levels of laser radiation.
•
No serviceable parts within. Unit is factory sealed.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury,
including eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment
includes but is not limited to:
•
Protective eyewear, protective clothing and gloves, and hearing protection.
WARNING
Summary of Contents for TapeLazer HP Automatic
