background image

10

308274

Parts

01829

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

16

30

31

Model 235490, Series A

Includes items 1 to 31

Ref
No.

Part No.

Description

Qty

Ref
No.

Part No.

Description

Qty

1

188354

RETAINING NUT

1

2

SPRAY TIP DISKS

235579

1/8 in. orifice 1

235580

1/4 in. orifice

1

235581

3/8 in. orifice 1

248311

5/16 in. orifice

1

. . . . . . . 

. . . 

. . . . . . . . . . . . . . . . . . . . . 

3

160225

LOCKRING, nozzle

1

4

188353

HOUSING ADAPTER

1

5

GUN NOZZLE  (all sizes included)

188428

Size 1

1

188429

Size 2

1

188430

Size 3

1

6

188447

VALVE STEM

1

7

111967

QUAD RING PACKING

1

8

188445

HEAD

1

9

160217

PIVOT PIN

1

10

160233

BOLT

1

11

235741

AIR CONTROL VALVE KIT

1

12

160231

SCREW, fluid valve regulating

1

13

111966

SPRING, fluid valve

1

14

160227

PUSH ROD, fluid valve

1

15

160232

GUIDE, spring and valve

1

16

156082

O-RING

2

17

150925

GASKET, copper

1

18

203953

LOCKSCREW, trigger

1

19

188446

GUN BODY

1

20

160215

TRIGGER LATCH

1

21

160222

AIR INLET ADAPTER, 3/8 npsm

1

22

n

154741

O-RING

1

23

161274

PLUG

1

24

160239

TRIGGER

1

25

161319

SPRING, air valve

1

26

177139

POPPET, valve

1

27

169643

AIR VALVE STEM

1

28

160910

WASHER

1

29

160229

AIR VALVE SEAT

1

30

160240

PACKING, air valve stem

1

31

160228

PACKING NUT, air valve stem

1

n

Keep these spare parts on hand to reduce down time.

241854 Kit includes 1, 2 (all sizes), and 4.

Summary of Contents for TexSpray 235490













Reviews: