background image

Ultra Max

t

Electric Airless Sprayers

Operating Instructions

The intent of these instructions is to provide the new painter with a quick and easy reference to
become familiar with airless sprayers. This does not replace the Instruction Manual supplied
with this sprayer. Read and understand the instructions and warnings in that manual. 

Important Note:

 The Graco Standard product line has a wide range of sprayer units that vary

slightly. The basic operations procedures are the same for all sprayers. Some illustrations may
not be applicable to the particular sprayer purchased.

Tools Required:

D

Two adjustable wrenches

D

Two 5 gallon metal pails

D

Grounding wires and clamps for pails

D

Pencil

Suggested proper clothing:

D

Respirator

D

Safety glasses

309273

Rev. D

How To Perform:

S

Component Identification

3

. . . . . . . 

S

Setup

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

S

Startup

7

. . . . . . . . . . . . . . . . . . . . . . . . . . 

S

SMARTCONTROL

t

9

. . . . . . . . . . . 

S

Cleanup

11

. . . . . . . . . . . . . . . . . . . . . . . . 

S

Trouble Shooting

 

15

. . . . . . . . . . . . . . 

S

Maintenance

16

. . . . . . . . . . . . . . . . . . . 

S

Storage

16

. . . . . . . . . . . . . . . . . . . . . . . . 

S

Tip Wear

16

. . . . . . . . . . . . . . . . . . . . . . . 

3300 psi (227 bar 22.7 MPa) Maximum Working Pressure

GRACO INC.

P.O. BOX 1441 MINNEAPOLIS, MN

55440–1441

E

COPYRIGHT 2000, GRACO INC.

Graco Inc. is registered to I.S. EN ISO 9001

Summary of Contents for Ultra Max 309273

















Reviews: