Graco XD30 Series Instructions Manual Download

Page: 10 / 10

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English. MM 3A0142

Graco Headquarters:

Minneapolis

International Offices:

Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

www.graco.com

12/2009

Leave ratchet (C) in place. Replace one screw (B)
(F

. 27).

Remove ratchet (C) from opening (D) (F

. 28).

Pull on hose to test tension (F

. 29).

If spring tension is still a little loose, reinsert ratchet
(C) in slot (D) and remove screw (B) again.

Turn ratchet (C) one full turn clockwise.

10. Repeat Steps 5 - 7 until tension is tight.

11. If spring tension is too tight, follow instructions for

Decreasing Spring Tension, beginning on page 7.

When spring tension is set correctly, replace and tighten
screws (B) and bolt (A).

Installing Dispensing Device

Install meter or dispense device to end of hose.

. 27

. 28

. 29

Summary of Contents for XD30 Series











Search results

Summary of Contents for XD30 Series

Reviews:

Related manuals for XD30 Series

Brands by name

Popular brands

Graco XD30 Series, Instructions Manual

Search results

Summary of Contents for XD30 Series

Reviews:

Related manuals for XD30 Series

Brands by name

Popular brands